NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622
NEW Quad Logic Brand G2 ATV Can Am Airbox Seal Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179
NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
New OEM Tail light assembly, with bulb, plug in and go! Fits late G1 and all G2L Outlander models. Part # 710001203
NEW OEM G1 Can Am Outlander Complete Seat Assembly. Part number 708001649 replaces 708000402, 708000507, 708000756, 715500323 Nonconforming foam issue on right hand side lower forward portion. It feels like the foam is rolled up inside of the cover. This is pictured and will go unnoticed to some. This is the G1 500 650 800 Outlander style but will install on G1 Renegade models.
Can Am OEM Upper ball joint NEW OLD STOCK Part number is 706201394
Can-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835
This is the XMR 1000 rear differential found in 2013-2018 800R 850 1000/1000R XMR.
It will fit g2 bikes (500/650/800/850/1000) if you are upgrading you will need to shorten your shaft 1.75? or buy a kit from us, please see our other listings.
This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential.
Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. If you are upgrading you will need a 20 spline end yoke to match.
In every way this is a beefier differential.
To bolt your driveshaft on this differential you will need a M10x1.25 16mm long bolt (not included)
Current part number 705503535
Old part number 705502546 705502178, 705502090
New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
NEW OEM Tool 529036302 This removes the large housing nut on G2 XMR Rear Differentials Also works on 2019 ATV Rear differential housing nuts. please note there may be some casting flare on your housing nut you may have to file to get the tool to fit, as it is a very tight fit.
O-Ring, this seals the rear differential case halves together. Fits: G2 2013-18 800R/850/1000/1000R XMR and 2019+ 650 or larger rear differentials. Unsure on fitment? Please contact us before ordering we will help. Part number 705501711
White wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715000537 & 715001378
BRAND NEW Can Am OEM Wheel Cap This is for a set of Four (4) Caps Part Number 705400928 There is more than one style. Please verify that this is the correct style BEFORE ordering.
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
Brand New OEM Water Pump Rotary Seal. Will fit most Can-Am models. Part Number 420650370
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932- OUT OF STOCK
NEW OEM Voltage Regulator Converts AC voltage from the stator to DC voltage used to charge the battery. Part Number 710001191 This is the 650watt version compatible with many ATVs with DPS if you have fitment questions please ask! - OUT OF STOCK
Brand New Genuine OEM front differential This is the visco 4lok model which has the electronic locking mechanism Part number 705403049 replaces 705402700 This is found in the 2021+ G2 XMR, XTP and XXC models. You will need to transfer over your fill plug after filling this with gear oil. 
OEM Rotax Cylinder Base gasket Fits many Canam ATV’s/UTV’s 330 400 500 650 800 1000 Unsure on fitment? Please ask! Part number 420630210
New OEM Engine Case Half Gasket. Fits most G2 Can-Am V-Twin Engines. This is for the longer stroke (75mm) cases. Old Part Number: 420651225 New Part Number: 420651227
NEW Can Am OEM Cam Timing Tool For holding the cam in place for timing and tightening camshaft sprocket bolts For easy installation of new timing chains or just setting timing. OEM Number 529036268 replaces 529036231- OUT OF STOCK
Brand New Genuine OEM XPS Synthetic Blend Oil Change Kit. Ultra convenient “all in one” kit saves time and money. For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest. Not compatible with Maverick X3 Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 5W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs. May not ship in original box Part Number: 779258 
NEW OEM O-rings and hex bolts to install inner CVT cover on most Can-Am V-twins. Works on 7 and 13 bolt inner covers Part numbers: O-rings - 420430407 and 420631087 old numbers 420430408 420631088 Hex Bolts - 420440207 Also has a nut and washer for 1000 cover installation - 232561434, 224061121 Will come as pictured
Brand New Genuine OEM XPS Full Synthetic Oil Change Kit. Ultra convenient “all in one” kit saves time and money. For Can-am off road vehicles with 500cc or larger Rotax engines. Excludes Traxter and Quest. Not compatible with Maverick X3 Includes 2 quarts plus 1 16 fl oz of 4T synthetic oil 0W40, 0-rings, rotax oil filter, and copper washer for old style and new style drain plugs. May not ship in original box Part Number: 779259
420927837 Thermostat Gasket
Sold Each, vtwin’s require two per engine.
- OUT OF STOCK
NEW OEM BRP Thermostat Current part number 709200406 replaces 709200383 This style is external from the cylinder head. If you are unsure on fitment please contact us. 
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
Sunburst yellow wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 709402053, 709402054 & 715001378
Brand New OEM Stator Cover Gasket for V-Twin Engines. Fits 2006-Current V twin’s Part number 420651201
Brand New Genuine OEM Start/Stop Switch
Will come as pictured
Works on many V-twin ATV’s Renegades and Outlanders
Will not work on 400’s
Please look at the plug style on your current switch. The buttons may be arranged differently than the switch you are replacing.
We have found this switch will work on all V-twins DPS or non DPS 2006 to 2015
Current Part number: 703500920 Replaces: 710003062 710002883 710003039 710004041
New OEM Differential Pinion Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs Gen 2 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL Measurements are shown: 70mm outside and 37mm inside Part number 705401481
SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
1652 G2 Standard Rear Differential Rebuild Kit Please note, application alone is not accurate enough, please measure your parts before ordering! There are a few options for rebuild kits, please measure your parts before ordering!! OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Paired with high quality aftermarket ball bearings along with double lip axle seals. If your differential has tapered roller bearings, this will not fit. This kit should be installed by an experienced technician. Shims are included as the gears will need to be set up in your cases. Note: the O rings are not included, this is a cost savings measure as they are generally reusable. This kit will only fit six mounting hole differentials. Measure your outer diameter of the pinion seal, it should measure 2 3/4" (70mm) Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential.
This is an OEM Canam part used in many Generation 2 atvs.
It does not have the bracket for the rear brake caliper on it.
This is an updated version with much more substantial webbing for improved support.
Fits:
2012 Outlander and Renegade 800, 1000
2013 to 2018 500/570/650/800/1000 Outlander Renegade
2011-2013 Commander 800 1000
2013-2018 XMR 570 and 650**WILL NOT FIT** XMR 1000 or XMR 800
WILL NOT FIT ALL 2019 Models, please contact us if you have a 2019.Current Part Number 703501019
Previous Part Numbers 703500878, 705501896, 705501419, 705501993
New OEM front differential axle seal
Outer diameter is 47mm
Inner Diameter is 25mm
Part numbers: 705401486 705401618
SHIPS FREE TO THE LOWER 48 STATES Squadron Green wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450 Both are brand new. Part numbers 715006117 & 715001378
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.