All Balls complete module, retaining nut and gasket This fits many G2 model ATVs please contact us if you have fitment questions. Part number: 1009-0139 47-1024 Replaces OEM numbers: 709000287 709000758
For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
Six Weights 21 gram each for CVtech Trailbloc Primary Part numbers: 0935-2054 or 0901-7118
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
Can Am Outlander 500 650 piston ring set New Genuine OEM Kit is only for one piston Current part number 420684384 Old part number 420684114
OEM Canam Projector High Beam projector head light assembly with 9005 bulb. Brand NEW! High quality HELLA brand made in Austria. Fits many models please ask if you are unsure! Part Number 710002525
Blue wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715003814 & 715001378
New G2 dual piston front left brake caliper with OEM pads. Fits G2 Renegade and Outlander 2012-2019 Genuine OEM part. Part number 705600862
New Demon Heavy Duty Axle Front Left Fits: G2 2012-2018 ATV Outlander/Renegade 500 570 650 800R 850 1000 1000R Part number PAXL-3070HD Replaces OEM 705400756 703500823 705401943 705401115 705401384 705401947 705401704 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Right (throttle side) Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3065HD Replaces OEM 705502711 705502713 705503024 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Rear Left Fits: 2019+ ATV Outlander/Renegade 650 850 1000R Part number PAXL-3064HD Replaces OEM 705502710 705503025 705502712 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.