OEM Snorkel kit, this raises the engine air intake well above the handlebars. The ECU is relocated to allow for CVT breather tubes to extend upward. This kit includes the brackets for the two plug type ECU found on ride by wire outlanders. With the tubes molded specifically for this application this is the cleanest kit you can install on your machine. Part number 715005999 Installation time is approximately 3.5 hours This snorkel kit is not compatible with the XT Handlebar Protector Kit (P/N 715000271)
-
SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential. -
Blue wrap around wind deflector set with mounting kit. Fits Outlander, Renegade, & DS450. Both are brand new. Part numbers 715003814 & 715001378 -
NEW OEM 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234 -
CVTech Trailbloc Nut for ribbed style clutches
This is the large nut that retains the outer clutch to the inner.
M22 diameter
Part number 0980-1015 replaced by 0980-1017
-
For use with all BRP turn key type ignition switches. Will not fit RFID type ignitions. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Be sure to match up one wire at a time when installing, this helps avoid switching wire orientation as the wires are not color coded. The wires are 6” long so it can be fixed inside the headlight pod Sold each; includes butt connectors and zip ties Part number 2120-0943 -
Moose Utility Division handlebars Replaces factory OEM handlebars 7/8? diameter standard size made from .083 steel tubing Pullback/Sweep: 4? Width: 32? Center Width: 5-1/2? Does not come with hand grips May fit other years or models Made in the U.S.A. Will come as pictured Replaces OEM Part Numbers: 709401240 709400877 709400292 Parts unlimited number: 0601-4379 -
All Balls complete module, retaining nut and gasket
This fits many G2 model ATVs please contact us if you have fitment questions.
Part number: 1009-0139 47-1024
Replaces OEM numbers: 709000287 709000758
-
Dual USB Power Outlet Kit A simple upgrade kit, plug and play Product Number: 219400510 replaces the existing 12v power outlet on your machine: 710001248
-
New Genuine OEM Intake neck for Outlander 1000, Renegade 1000, Commander 1000 and Maverick 1000 Turbo Old part number 420267040 420267041 Current part number 420267042 -
NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX -
Brand New Genuine OEM head light For G2L.
This housing is for both the high and low beams on a G2L model.
The lens is roughly Five inches across.
710003900
If you have steel racks on a 2015 or newer Can Am ATV you have a G2L.
New in package. Comes as pictured.
This will not fit G2 or G1 regular Outlanders.
