- OUT OF STOCKG2 dual piston brake calipers with pads. Genuine OEM parts. This set of three calipers will fit G2 Renegade and Outlander 2012+ Part numbers 705600861 705600862 705600859 Cleaned greased and ready to install.
- OUT OF STOCKSHIPS FREE TO THE LOWER 48 STATES New Forged OEM Can-am piston kit with rings. Matched to an OEM Rotax used Cylinder. This is ready to install on your 650 Outlander engine. Two are required per engine. Piston comes with rings installed. Piston pin, and clips are not included. Part number 420684111 420613888
- High quality Timken oil seal. Replace a leaking front output seal on your canam. This is the seal that seals the engine through shaft coming out of the front of your Vtwin engine below the front exhaust header. To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM part numbers: 420430588 420430589 420430580
- This model type is a rubber O.D. seal with two sealing lips. The main sealing lip is spring loaded. This is a two-way seal, which means that it can retain lubricant and exclude contaminants simultaneously Canam Vtwin crankshaft main seal. Replaces OEM number 420631933 This seal is pressed into the PTO cover on v-twin's Unsure on fitment? Just measure you seal. 52mm Outer Diameter 34mm Inner Diameter 8mm Thick
- Sale!New take off gearbox side, 20 spline yoke. This fits on large gearboxes output shafts. 20 spline yoke partially machined to accept a protector ring. This is the forward most yoke on the REAR driveshaft. Works with 398 U joints. found on Vtwin rear driveshafts. Part number 715900129 replaces 705501373 and 715900234
- NEW Take Off G2 Can Am Outlander Front Diff Assembly 703500900 Unit-51. Part number 703500900 Pulled From Machine With 9.5 Miles. This fits 2006 and newer machines. Please note this is the visco lok style differential non electronic, for use with machine equipped with DPS, as this locks up quicker than the non DPS style. If you have fitment questions please contact us!
- SHIPS FREE TO THE LOWER 48 STATES Set of Bearings and Seals to Rebuild Your Front Differential on Your Can-Am Fits Most Can-Am Models from 2007-Current (WILL NOT FIT Maverick X3/Sport/Trail or Defender) This Kit has High Quality Aftermarket Bearings which are: Timken, SKF, NSK, KOYO, Nachi Comes with: 2 - Carrier Bearings- SKF Brand 2 - Axle Bearings- OEM NSK Japan made 2 - Axles Seals- Timken 1 - Inner Pinion Bearing- Nachi Japan made 1 - Large Pinion Bearing- Koyo Japan made 1 - Pinion Seal
- SHIPS FREE TO THE LOWER 48 STATES This is the high end XMR rear differential replacement. The differential has all forged Carburized (case hardened) alloy gears, and high end bearings inside billet cases. These gears are set up to very specific tolerances, ready for years of abuse. These are sold with a six month warranty on the gears, lifetime on the cases. These gears require a break in period of 75-100 miles This is the aftermarket upgraded XMR 1000 rear differential found in 2013-18 1000/1000R XMR. You will have to clearance your surrounding brackets to install as this is a beefier case. The drain plug access hole in your frame may have to be enlarged also. It is also used in the G2 800 XMR & 850 XMR. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75" or by purchasing a conversion shaft, we can help with application, please ask! (G1 bikes will require further modifications to work). This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size when comparing it to the standard differential. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential. Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. In every way this is a beefier differential. Replaces current part numbers 705502178, 705502090 this does not have the ABS sensor hole.
- Made in the USA Specialized ATV, made some strong, tough rods that will hold up to whatever kind of riding you like. 6061 Billet Rods with 5/8 heim joints and all the needed hardware to install. 1 set comes with 2 tie rods and complete assembled heims and hardware. Fits G2 Outlanders and Renegades 2012+ (even the wider 2019+ machines)
- Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. Two inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1037
- Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. 1.5 inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1036
- Rugged wheels spacers are made from T6061 aluminum alloy and are precisely CNC machined for accurate dimensions. Spacers can be direct bolt on and can use OEM studs. If you are looking to widen the stance of your machine, clear larger tires or get some new wheels. These spacers are just what you need. These spacers are sold as a pair. One inch thick The bolt pattern is 4x137mm M10 studs Part number PAWS-1035
- OUT OF STOCKNEW Quad Logic Brand G2 ATV Can Am Airbox Seal Part number 500-1139-PU This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179