NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
NEW OEM G2 ATV Battery Hold Down Fixation Plate Kit. This retains the battery in place, and gives your seat something to latch into Kit includes:
Fixation Plate 710009129 replaces 710002404 Positive Battery Terminal Cover 710006729 Rubber Stopper 705014429 Three aftermarket stainless bolts
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs:
80 ft·lb On the Primary Bolt
45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
New short wiring harness for rear tail lights Will need to be wired in to work. This plugs in to Tail light part number 710001645 Fits: G2 ATV's with dual tail lights, Commanders, and Mavericks (non X3/Sport/Trail)
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter.
Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
Air Filter for G1 Outlander and Renegades. Replaces OEM 707800174 Fits 500, 650, and 800HO NON-R 800 engines, from 2006 – 2012. Bonded, two-layer .65" foam designed for maximum protection and airflow Coarse outer foam traps large particles while fine inner foam catches the finest dust With the precision pre-oiled air filter, there is no excess oil to rob horsepower, and no dry spots endangering your engine Made in the U.S.A.
EPI Ball Joint Kit G1 Fits Outlander 650/800 Upper
Renegade 500/800 Lower or Upper Heavy Duty Steel housing with isolated design joint for long life Ball joint includes ball joint, rubber boot, snap ring and cotter pin EPI Part Number: WE351039 P/U Part Number: 0430-0610 Replaces OEM Part Number: 706200653
Can-am Rubber Trailing Arm cover and Oetiker clamp for your G1 Outlander or Renegade Will only work on the gen 1 Outlander and Renegades 2006-11 and some 2012 models. If you are unsure on fitment, please ask. You will need to order qty 2 to replace both sides. Genuine OEM parts Part Numbers: 706000222 706000749 293650162
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
Preferences
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
Statistics
The technical storage or access that is used exclusively for statistical purposes.The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
Marketing
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.