Sliding Sheave for CVTech Canam Clutches
Part Number 0910-0006
NEW OEM Throttle Body Air Intake Neck Fits 850/1000 ATVs and 800R/10000 Commanders On ATV’s this connects the throttle body to the intake manifold On Commanders this connect the “Y” intake manifold to the 90* fitting Part number: 420267045
EPI Lower Ball Joint Fits: G1 Outlanders 400 500 650 800 Replaces OEM: 706200444 This style of ball joint bolts to the lower control arm. If you are unsure of fitment, please ask! 2006 - 2014 Can-Am Outlander 400 2007 - 2012 Can-Am Outlander 500 2008 - 2012 Can-Am Outlander 650 2006 - 2011 Can-Am Outlander 800 2006 - 2013 Can-Am Outlander Max 400 2007 - 2013 Can-Am Outlander Max 500 2007 - 2012 Can-Am Outlander Max 650 2006 - 2012 Can-Am Outlander Max 800
Brand New Genuine OEM ignition key switch for Outlander G1 or Renegade G1 Does not require BUDS tuning to swap out, your current DESS key will turn in this. The ignition switch is just a reader of the coded key. Key sold separately. Old Part Numbers 710000728 and 710001421
Genuine OEM Start/Stop Switch
This has the additional single light blue wire with connector.
Current Part Number: 710006134
Fits some 2019 Outlander and Renegade 1000R, 2020 Outlander and Renegade 850/1000R
Please contact us if you are not 100% sure on fitment, we will be happy to assist
Plain bearing half 40 X 43 X 15 This fits into one side of the connecting rod. part number 420233980
SHIPS FREE TO THE LOWER 48 STATES New genuine Can-am rear prop shaft for outlander 1000 xmr. (MAX length minus 1.75”) This is an oem part, we do not cut, phase, balance or otherwise modify this shaft. It will work on 2012-14 Outlander 1000 MAX ATV's with the XMR rear differential also. 20 Spline Gearbox Yoke 20 Spline Differential Yoke Current Part number: 703500989 Previous Part number: 703500859, 705501720, 703500927
Six Weights 12 gram each for CVtech Trailbloc Primary Part numbers: 0935-2004 0901-7104
SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
Wind deflector mounting kit with hardware. Fits Outlander Renegade & DS450. For use with OEM wind deflectors This is just the mounting kit. Part number 715001378 No wind deflectors included.
OEM CANAM BRP Exhuast Muffler Clamp Part Number 293650177 Fits 2.25" OD pipe
NEW OEM Can-am Output Crank Shaft Seal This is the engine out put shaft seal, pressed into the crankcase PTO cover 34mm Inner Diameter 52mm Outer Diameter 8mm Thick Current Part Number 420631933 Replaces Part Number 420631932
