NEW OEM Tool 529036302 This removes the large housing nut on G2 XMR Rear Differentials Also works on 2019 ATV Rear differential housing nuts. please note there may be some casting flare on your housing nut you may have to file to get the tool to fit, as it is a very tight fit.
New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
This is the XMR 1000 rear differential found in 2013-2018 800R 850 1000/1000R XMR.
It will fit g2 bikes (500/650/800/850/1000) if you are upgrading you will need to shorten your shaft 1.75? or buy a kit from us, please see our other listings.
This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential.
Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. If you are upgrading you will need a 20 spline end yoke to match.
In every way this is a beefier differential.
To bolt your driveshaft on this differential you will need a M10x1.25 16mm long bolt (not included)
Current part number 705503535
Old part number 705502546 705502178, 705502090- OUT OF STOCK
Can-am Shim Kit for XMR G2 800 or larger 2012-current Rear Differentials. Part number 703500835 
NEW Speed Sensor Quad Logic brand Will fit 2006-Current Outlander, Renegade, Maverick, Maverick X3, Commander, and Defenders 2210-0568 500-1024 Replaces OE Numbers 420265621, 420265622, 420265624, 420265625, 420265626, 420265629, 707000745 and 711265622
SHIPS FREE TO THE LOWER 48 STATES This is the high end XMR rear differential replacement. The differential has all forged Carburized (case hardened) alloy gears, and high end bearings inside billet cases. These gears are set up to very specific tolerances, ready for years of abuse. These are sold with a six month warranty on the gears, lifetime on the cases. These gears require a break in period of 75-100 miles This is the aftermarket upgraded XMR 1000 rear differential found in 2013-18 1000/1000R XMR. You will have to clearance your surrounding brackets to install as this is a beefier case. The drain plug access hole in your frame may have to be enlarged also. It is also used in the G2 800 XMR & 850 XMR. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75" or by purchasing a conversion shaft, we can help with application, please ask! (G1 bikes will require further modifications to work). This differential has automotive style cut gears, tapered roller bearings, along with an overall larger gear size when comparing it to the standard differential. There are a total of three bearings on the pinion gear giving it much more support over the standard rear differentials, this requires a shorter driveshaft, as mentioned earlier if you are swapping this in place of a standard differential. Pinion spline count 20, standard differentials use 18 spline pinion shafts, that are smaller in diameter. In every way this is a beefier differential. Replaces current part numbers 705502178, 705502090 this does not have the ABS sensor hole.
SHIPS FREE TO THE LOWER 48 STATES Set of Bearings and Seals to Rebuild Your Front Differential on Your Can-Am Fits Most Can-Am Models from 2007-Current (WILL NOT FIT Maverick X3/Sport/Trail or Defender) This Kit has High Quality Aftermarket Bearings which are: Timken, SKF, NSK, KOYO, Nachi Comes with: 2 - Carrier Bearings- SKF Brand 2 - Axle Bearings- OEM NSK Japan made 2 - Axles Seals- Timken 1 - Inner Pinion Bearing- Nachi Japan made 1 - Large Pinion Bearing- Koyo Japan made 1 - Pinion Seal
NEW Take Off G2 Can Am Outlander Front Diff Assembly 703500900 Unit-51. Part number 703500900 Pulled From Machine With 9.5 Miles. This fits 2006 and newer machines. Please note this is the visco lok style differential non electronic, for use with machine equipped with DPS, as this locks up quicker than the non DPS style. If you have fitment questions please contact us!
High quality Timken oil seal. Replace a leaking front output seal on your canam. This is the seal that seals the engine through shaft coming out of the front of your Vtwin engine below the front exhaust header. To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM part numbers: 420430588 420430589 420430580
Cam Am rubber bellows for front differential or rear differential This is a brand new OEM rubber breather and a OEM Oetiker Clamp Bellows Part # 705400352
This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials- High quality Timken axle oil seal. Fits ATV front differentials 2006-current, some UTV's To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500255 705500081 Order qty two per machine.
High quality Timken axle oil seal. Fits ATV rear differentials 2006-2014 To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 30mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500751 705501196 and 705501996 Order qty two per machine.
SHIPS FREE TO THE LOWER 48 STATES This will replace the functionality of the VISCO Lock in any Can-am Front differential. 2006 to Current including X3. Installs in place of the “spider gears” Will not fit models with an electronic smart lok front differential Very simple to install. One measurement to make. The TORQ Locker is the most advanced, strongest, highest quality automatic locking differential on the planet, proven in the most extreme vehicles from hard-core Rock Crawling, racing the King of the Hammers, Rock Bouncing, Sand Dunes and Mud Drags. To back this all up, Torq-Masters Industries offers an unprecedented 2 year warranty on the TORQ Locker with no tire size, horsepower limits or loopholes. Torq-Masters Industries is committed to building the highest quality locking differentials possible. To be the best, we build with the best, TORQ Locker is 100 percent Made in the USA with 100 percent USA raw materials. Keep it Simple, no air-lines to leak, compressors to fail, cables to adjust or electrical gremlins, the TORQ Locker gives you piece of mind as a reliable, mechanical, automatic locker that can handle any terrain. The TORQ Locker design eliminates and integrates pesky locker components seen in all other automatic drop-in lockers. The spacers are gone and the dowel pins are now machined into the Cam Gears to form key-ways. The innovative design features of the TORQ Locker have three game-changing benefits: No dowel pins to install or fail. The Key-Way design of the Cam gears can’t shear, ever. Easiest Locker on the market to install, no spacers, no dowel pins, one measurement. Best On-Road manners of any automatic locker; the Key-Way design is more forgiving than the rigid dowel pin design. The Key-Way allows for smoother locker engagement. By eliminating the spacers they eliminated the leading cause of the pop some people experience with automatic lockers. Listing is for the TORQ Locker only. Differential carrier shown in pictures is for reference only.- OUT OF STOCK
Aftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.