- OUT OF STOCKNew OEM 2019+ rear differential gear set, 10/36 tooth straight cut ring and pinion gear set, Timken seals, NTN or IKO pilot bearing , OEM shim kit and OEM bearings along with a new bolt and washer to retain the driveshaft. BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Fits differential part numbers: 705502808, 705502546, 705502178, 705502090 703501031 705501550 705501556 705501557
- SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16" (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- 2012-2018 G2 ATV Rear Differential Swap Kit Kit includes: Rear Differential, Rear driveshaft, Bolt and Washer. This kit includes a rear differential with: Tapered roller bearings Three bearings on the pinion gear 6 inch diameter ring gear Your choice of gear style, spiral bevel or straight cut. Both have the same 3.60 ratio as your current differential. Spiral Bevel Gears are sourced from the 2013-18 800 850 and 1000 XMR differentials. Current part number 705502546 Old part numbers: 705502178 & 705502090 Straight Cut gears are sourced from the 2019+ 650+ differentials. Current part number 705502808 The driveshaft included is an OEM shaft with the correct end yokes for your application. The differential end yoke will not use a wear ring, this has been done away with by BRP the yoke is what the pinion seal touches now. You will need to fill the differential with 250ml (8.4oz) of 75W-140 gear oil and transfer over your fill plug and washer. The torque spec on the driveshaft retaining bolt is 55ftlbs with thread locker applied. Some minor trimming on the brackets that surround the differential is required. These differentials have the provision for an ABS sensor, this is standard on euro models, for mud riders state side, you can fill this hole with RTV or leave it open. If you are running the silver protector ring on your axle, you will need to push the ring outward slightly. We choose to remove these dust covers as they tend to trap debris when run under water.
- OUT OF STOCKAftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863- NEW Take Off G2 Can Am Outlander Front Diff Assembly 703500900 Unit-51. Part number 703500900 Pulled From Machine With 9.5 Miles. This fits 2006 and newer machines. Please note this is the visco lok style differential non electronic, for use with machine equipped with DPS, as this locks up quicker than the non DPS style. If you have fitment questions please contact us!