- NEW Take Off G2 Can Am Outlander Front Diff Assembly 703500900 Unit-51. Part number 703500900 Pulled From Machine With 9.5 Miles. This fits 2006 and newer machines. Please note this is the visco lok style differential non electronic, for use with machine equipped with DPS, as this locks up quicker than the non DPS style. If you have fitment questions please contact us!
- OUT OF STOCKAftermarket Four wheel drive servo motor. This is what engages the sliding collar putting power to the front differential. Part number 715900614 420891087 415129174
- OUT OF STOCKNEW OEM Large Gearbox NEW OEM Can-am Part NOT A REBUILD, ALL NEW Brand New In The Box Part number 420686214 This gearbox is used in the following: 2019-2024 Renegade/Outlander 1000R XMR If unsure of fitment, please contact us. We will be happy to help!
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863- New Oem Canam Pinion nut, this is spun on to the pinion gear to retain the bearings on the pinion gear of xmr differentials on ATV XMR's G2 800/850/1000/1000R This is not needed on 570 or 650 XMR models The threads are M28x1.25 Right Hand the outer diameter is 51mm Please check that this is the correct nut for your application Part number 705501550
- New Can Am ATV Low Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.
- New Can-Am GEAR BOX
- Current Part Number- 420686612
- Replaces: 420684820, 420684824, 420684825, 420684827
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Low Ratio (6.4% Lower HIGH Range) gearbox than a standard 800 gearbox.
- This is found in Outlander or Renegade 500's, Outlander 650's and the Outlander 800R XMR
- SHIPS FREE TO THE LOWER 48 STATES NEW OEM Canam Parts OEM 14% LOWER LOW GEAR SET for most every 1000 Vtwins minus north american 2015 and newer outlander 1000/1000R This is the way to reduce the over all Low Gear ratio on your can-am 1000 running larger tires. This is the LOW RATIO for any Large Gearbox. The last picture shows a Large gearbox. This will not fit Small Gearboxes. 14% lower gear ratio than standard 1000 gear boxes (Maverick, Commander, Renegade, Outlander) Will also fit 800 Commander
- New Can Am ATV 800 Standard Ratio Small Gear Box / Transmission Will work on all Can-am Vtwin 500/570/650/800/850 Both Outlander or Renegade.
- New Can-Am GEAR BOX
- Current Part Number- 420686714
- Replaces: 420684780, 420685391, 420685392, 420685394, 420685396, 420685397
- NEW OEM Canam Part NOT A REBUILD, ALL NEW
- This is the Standard Ratio gearbox for any 500/570/650/800/850 v twin Can-am, Renegade or Outlander.
There are a few options for kits, please verify your differential uses this style of gears before ordering!
This will only fit six mounting hole differentials.
Late G1 Early G2 Standard Rear Differential Ring 36t and Pinion 10t gear set Pinion bolt size is M10, this may be different than what you are replacing.
OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. This kit should be installed by an experienced technician.
Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4? (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
- This is the 2019+ rear differential found in Renegades and Outlanders 650 and larger This has the 6 inch (155mm) ring gear with straight cut teeth as shown. It will fit g2 bikes (500/650/800/1000) if you are upgrading you will need to shorten your shaft 1.75 inches or buy a kit from us, please see our other listings. (G1 bikes will require further modifications to work). This has a provision for an abs sensor, but will fit bikes without a rear diff sensor BRP claims 25% increase in load capacity on this gear set vs the spiral cut xmr final drive units (rear differentials) from 13-18 models. Pinion spline count 20 Current part number 705502808
- SHIPS FREE TO THE LOWER 48 STATES New OEM Standard G2 Rear Differential Ring & Pinion Gear Set 1652 There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. OEM Rear Differential Gear set 10/36 Ring and Pinion gear set. The gears are straight cut as pictured. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16? (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8? (16mm) Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 -2019 G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential. 570/650 XMR machines do not have the true XMR differential.
- NEW OEM GEARBOX 570s come with a lower ratio gearbox than the normal low ratio gearboxes found in the 650’s and 500’s The extra low ratio gearbox will help bottom end power and with larger tires, this is the lowest ratio small gearbox. Current Part Number 420686569 Replaces: 420686567 420686560 420686561 This is found in Outlander or Renegade 570 DPS XT or XMR Will work in 650,800,850, and 2015 and newer 1000/1000R ATV’s Teeth count and gear ratio Ring & Pinion 38/28 = 1.357 High Gear set 46/20 = 2.300 Low Gear set 31/14 = 2.214 High final ratio 3.341:1 Low final ratio 5.662:1 2015 and newer non XMR outlander 1000’s have this style gearbox, if you have fitment questions, please contact us! If you are installing this on an early G1 ATV you will need to transfer over your gear position sensors.