Can-am Style Plastic Fender rivet set. NEW Pack of 25 For 8mm (5/16?) holes great for holding plastic fenders together, works on Maverick, Commander, Outlander and Renegade Replaces part numbers 293150089 293150230
HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
Replaces OEM part number 420222691 Upgrade your plastic thermostat housings/water neck on your vtwin 500/570/650/800/850/1000 SOLD AS PAIR These will work in Commanders, Mavericks, Outlanders & Renegades
NEW OEM Can-am rear driveshaft retaining bolts. Don’t know your size? These are the two most common sizes. M12 x 16 and M10 x 16 with washers. Ships exactly as pictured. On the M12x16 bolt we recommend adding thread locking compound before installation. Thread pitch is 1.25
Fits G2 ATV’s Outlander or Renegade 500 450 570 650 800 850 1000 1000R
Shift Arm Base Upgrade
Replaces OEM 707003054 707000971 707002439
USA made Made from 6061 T6 Aluminum (aircraft grade)
This plate does not require any additional hardware, use a zip tie to retain the wire harness or vent lines running near it.
NEW Prop Shaft Low profile pair of clamps for 715900118 boot. Clamps also work for G2 front shaft boot 705401093. The last few pictures show the clamps loose, then installed nice and tight. Sold in pairs enough to do one boot.
Cast Aluminum Valve cover set with Stainless bolts. Replaces your factory plastic valve covers on any can-am V-twin ATV or UTV If you have aftermarket camshafts you may need to clearance the cover with a dremel. 500/570/650/800/850/1000/1000R Replaces OE Numbers: 420610390 420610394 420610393 420610395
Single CVT cover bolt with the hex head and torx inside. The preferred style to work with. Part number 420440568 replaces 420440567 420440307 Genuine OEM Part A little anti-seize is a great idea when installing these bolts, as the inserts they screw into can easily strip out.
M8x1.25×70 Bolt. m8-1.25x70mm Used to open the secondary clutch on many Can-am ATV’s & SXS’s Simple tool, trusted seller. Or just use these specs and head to your hardware store.
Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
420927837 Thermostat Gasket Sold Each, vtwin’s require two per engine.
Rear driveshaft U-Joint Replacement 398 style Fits all V-twin Canam rear driveshafts XMR XT XXC XDS XRS STD Grease zerk in cap for easy maintenance Made in Japan High Quality Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation. Please note on some older driveshafts the yoke ears may need to be ground down to allow for the larger center part of the joint to be installed. Replaces OEM part numbers: 703500846 715900270 715900278
New OEM Can-am Part This boot fits the G2 outlander/renegade front driveshaft. It is the thicker tapered boot, some use two of these on G2 atv's front driveshaft. Part number 705401093
New Aftermarket Bellows with clamp, use this in place of vent lines on your differentials. Replaces OEM part number: 705400352
Brand New Genuine OEM Fill Level Plug Be sure that yours looks the same due to other styles for front or rear differential from different years M14 diameter 1.5 thread pitch Part number 705500504
New OEM Rear driveshaft U-Joint 25mm caps 398 style Fits all V-twin Can Am rear driveshafts Clips are included just as pictured We recommend pumping fresh grease in after installing, as the grease inside may not be enough for operation.
Rear Differential Seal kit for differentials with 80mm outer diameter pinion seal
1 Pinion Seal, 80mm
2 Axle Seals, 52mmBrands we use include : Timken, Dichtomatik and SKF
Fits:
2013 to Current Outlander 1000/1000R XMR
2015 to Current Outlander 800/850 Xmr
2016 to Current Renegade 1000R XMR
2019 to Current 650 and Larger ATVs
Also some 2019 to Current 570 XMR (measure your parts to verify fitment)*** THIS WILL NOT WORK IN 2013-2018 650/570 XMR or 2011/2012 800 XMR machines. If you are unsure about fitment please contact us! ***
One CVT cover screw with the Torx head. M6 X 30.5 Stainless Part # 420440561
Cam Am rubber bellow for front or rear differential. This is a brand new OEM rubber bellows. Part number 705400352
293370019 NEW OEM BRP Clip Retains the wheel bearing in the knuckle on many machines Unsure on fitment? Please ask us, we will do our best to help.
Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials
Can-am Outlander, Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential.
This is an OEM Canam part used in many Generation 2 atvs.
It does not have the bracket for the rear brake caliper on it.
This is an updated version with much more substantial webbing for improved support.
Fits:
2012 Outlander and Renegade 800, 1000
2013 to 2018 500/570/650/800/1000 Outlander Renegade
2011-2013 Commander 800 1000
2013-2018 XMR 570 and 650**WILL NOT FIT** XMR 1000 or XMR 800
WILL NOT FIT ALL 2019 Models, please contact us if you have a 2019.Current Part Number 703501019
Previous Part Numbers 703500878, 705501896, 705501419, 705501993
Brand New Genuine OEM Rubber Boot Fits Commanders Mavericks Outlanders Renegades Used for sliding joints Part number 715900118
SHIPS FREE TO THE LOWER 48 STATES NEW OEM Can Am Updated Cam Chain and Updated Guide Set 2006-Current V Twins 500, 570, 650, 800 These chains and guides are a common issue on 2006-2008 500/650/800 V-twin ATV’s. The chains fail and start cutting the plastic guides. One of two things happen: One, the Camshaft (generally the front cylinder head, first) becomes out of time, and the valves hit the piston. Two, the oil pick up screen becomes clogged with guide material. Engine oil can not be cycled through the engine, generally this spins the big end connecting rod bearings. This kit includes updated chains and guides, totally avoiding this problem. Order QTY 1 (one) per engine. Kit includes: 2 Chains 420297063 2 pivot guides 420436015 2 fixed guides 420236584 2 bottom guides 420236351 Will not work on 1000/1000R Engines To install the timing chain kit you will need to remove the PTO Cover, Stator Cover, and Cylinder Heads. We sell the gaskets and pullers required to do this. Check our other listings for these products- OUT OF STOCK
NEW Outsiders Mud Crew Airbox seal This is an improved design over factory Apply a small amount of grease to aid install, this is much thicker and denser than the OEM o-ring or gasket Replaces OEM part numbers: 293300165 293300175 293300179 
Outlander Renegade Commander Maverick Differential Drain Plug Brand New Genuine OEM Drain Plug 9.9 mm outside diameter Will fit on some fronts and rears be sure yours looks like this one and measures the same Part Number 705500894
Right Side Front or Rear for G2 ATV 2012 with dual piston calipers 2013-19 To current G2/G2L One Caliper Set Part number: DP516 1721-1449 Replaces OEM # 715900249 705601014 DP Brakes Brake Pads are designed with sintered metal compounds to give your ATV high-tech performance in all conditions Pads have a quick break-in period so you get maximum performance fast DP Brakes design and materials ensure consistent, hard stops and fade-free performance Sintered metal compounds outlast more conventional organic or aramid fiber pads
New Genuine OEM CVT Cover Drain Plug This clamps on to your outer cvt cover. Part number 707001179
New Can Am spark plug boot connector part number 420265020 Will only work with spark plug style that is pictured Easy to replace. Just unscrew your old one and screw on your new one. Fits: 2013-2018 Maverick 1000R Turbo or Non Turbo 2018-2020 Commander 1000R 2016-2020 Outlander or Renegade 850/1000R 2015+ Outlander 450
EPI brand Wheel bearing Greaser Tool for bearings with 30mm inner diameter Quick and easy way to extend the life of your wheel bearings 10 pumps of marine rated grease into a new wheel bearing will extend the bearing’s life High quality CNC machined with precision drilled grease channel Axle stub needs to be removed to use the tool. Part numbers: 3811-0094 CA30MMGREASER-O
NEW CV Tech Primary Clutch Puller for can am ATVs Replaces OEM puller part number 529035746 7/8" Hex Head Measurements listed in picture We have found this to work on both the ATV factory primary and CV tech primary clutches. THIS IS NOT A TOOL RENTAL, IF YOU USE THE TOOL YOU OWN IT!
5280 Rear Differential Tapered Roller Bearings and Seal kit 1 Pinion Seal, 80mm outer diameter 2 Axle Seals, 52mm outer diameter 1 Thick Tapered Roller Bearing 3 Thin Tapered Roller Bearing 1 Needle Bearing These are High Quality aftermarket parts, as good or better than OEM! Brands include FAG, NTN, IKO, TIMKEN, KOYO, SKF, Dichtomatik. BRP does not sell these bearings alone, we have taken the guess work out of replacing these parts. Fits: 2019 to Current 650 and Larger ATVs 2013 to Current Outlander 1000/1000R XMR 2015 to Current Outlander 800/850 XMR 2016 to Current Renegade 1000R XMR some 2019 to Current 570 XMR (measure your parts to verify fitment) *** THIS WILL NOT WORK IN 2013-2018 650/570 XMR or 2011/2012 800 XMR machines. If you are unsure about fitment, please contact us! *** Fits differential part numbers: 705502808, 705502546, 705502178, 705502090
NGK 4339 DCPR8E Standard Plug Fits All G1 ATV's OE numbers: 707000246 715900637 Thread Size: 12mm Thread Pitch: 1.25mm Seat Type: Gasket Resistor Value: 5K Ohm Reach: 19mm (3/4") Hex Size: 5/8" (16mm) Terminal Type: Removable Nut (you will need to remove this for use on G1 ATV's) Gap: .028" (0.7mm) Torque Specs Aluminum: 10.8-14.5 lb. ft. Brand: NGK Heat Range: 8 Longevity: 30k Miles Resistor: Yes Projected Material: Nickel Quantity: 1
Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
CVT Rear Boot (the boot that connects to the exhaust side of the inner CVT cover plate. This is the updated part and will work on all G1 V-Twin ATV’s . This replaces 707000789, this newer style will not work on the xmr 2011-12 where the exhaust riser pipe meets the upper tube. Current Part Number 707001274
SHIPS FREE TO THE LOWER 48 STATES Updated Can-am Rear G2 Outlander/Renegade 2019 and newer prop shaft. All new all OEM Shaft OEM U-joints. OEM protector ring installed Input yoke swapped to 18 spline This is the correct length for short wheel base single seat 500/570/650/800/850 Outlander or Renegade with 1000 XMR rear differential. This will also work on 2015+ Outlander short wheel base, single seat 1000/1000R with 1000 XMR rear differential. Direct replacement for 2015 and newer 800/850 XMR Current Part number: 703500988 Previous Part number: 703500858 703500931 20 spline differential side yoke 18 spline gearbox side yoke No wear ring needed
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.