NEW CV Tech Primary Clutch Puller for can am ATVs Replaces OEM puller part number 529035746 7/8" Hex Head Measurements listed in picture We have found this to work on both the ATV factory primary and CV tech primary clutches. THIS IS NOT A TOOL RENTAL, IF YOU USE THE TOOL YOU OWN IT!
Can Am Maverick X3 Maverick Sport/Trail or Defender Belt change kit. M36x2.0 thread size works on all X3’s and Defenders Will not fit QRS clutches found on “OG” mavericks This is a OEM tool and bolt Spreader It is recommended to use a coin in between the bolt and the clutch to avoid marring up the clutch. The bolt has the correct T30 bit on one end to remove the cvt cover bolts with your 13mm wrench/socket. We highly suggest a ratchet and T30 socket on a 3 inch extension to speed up the job. Part number 708200720 and 529000088 This set works in place of 708200686
New OEM Cap Fits on cover 420212500 Comes with 0-ring 420250050 Fits the following machines 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
Brand NEW OEM Genuine Transmission Belt 422280652 High Performance Drive V Belt TCIC (Turbo Charged Inter Cooled) Factory on 2020 Maverick X3 Turbo R R 195 HP models These will retro fit on all Maverick X3 models along with Defender H8/HD10 Maverick Sport/Trail. IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT. FITMENT QUESTIONS?? PLEASE ASK! Comes as pictured
New OEM Inner Variator Cover for Maverick X3 and X3 MAX Part Number 420212605 420212609 updated to 420212707
Drive Belt Can Am Fits: 2017-2020 X3 Maverick Turbo R Turbo RR 900HO 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8 OEM # 422280651 / 417300383 / 422280654 / 422280652IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.FITMENT QUESTIONS?? PLEASE ASK!World’s Best Belt Line- Latest generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market.
- Highest shock load rating to date being able to withstand the power of the 400hp machines.
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
- Latest bottom cog design for greater rotational efficiency at full shift.
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
- Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
- Increased cord pop-out resistance.
SHIPS FREE TO THE LOWER 48 STATES New OEM Outer Variator Cover for Maverick X3 and X3 MAX Part Number 420212508 replaces 420212505
New OEM Variator Gasket for Maverick X3 and X3 MAX Fits 2017+ Part Number: 420450405 Comes as pictured
Drive Belt Can Am Fits: 2017-2020 Maverick X3 900HO Turbo R Turbo RR 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8
Replaces OEM # 422280651 / 417300383 / 422280654 / 422280652 Gates Part number 48R4289 If you have fitment questions, please ask, we are here to help.
IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.
FEATURES AND BENEFITS
Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity - making it one of the most efficient CVT belts currently on the market.- First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
- Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
- Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
- Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
- Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
- Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.
DON’T BREAK YOUR BELT. BREAK IT IN.
If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.
1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)
2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.
NEW EPI Primary Clutch Puller. PCP-15 (PCP15)
Fits: Can-Am 1000 Defender 2016+ HD8 DH10
Maverick Trail 2018+ 1000
Maverick Sport (all) 2018+
Maverick X3 (all models) 2017+Replaces oem 529000064
One piece style, manufactured from the highest quality steel
Precise machining on every model for accuracy
Heat treated for superior strength
NEW Gboost Primary Clutch Puller. DCP19
Fits: Can-Am
Defender 2016-20 HD8 DH10
Maverick Trail 2018+
Maverick Sport (all) 2018+
Maverick X3 (all models) 2017+Replaces oem 529000064
All GBoost pullers start out with annealed, cold-rolled alloy steel.
Oil Quenched
Tempered
Rockwell hardness between 50-55
Zinc plated to prevent rust and thread deterioration
Machined to exact specifications in the U.S.A.
This results in31% higher tensile strength
19% higher yield strength
Stronger than any existing OEM pullers- OUT OF STOCK
Brand NEW OEM Genuine CVT Transmission Drive V Belt Will fit Maverick and X3. Will also fit other machines. Must check part numbers to confirm fitment. Will work on Ski Doo snowmobiles as well Current Part Number 417300531 Old Part Number 422280651 IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT. FITMENT QUESTIONS?? PLEASE ASK!
- OUT OF STOCK
NEW OEM Can Am Tool M8x1.25 Tapered Bolt Part number 529036098. This tool fills a few roles, used to open the secondary clutch on many models. This will also lock the crankshaft on Vtwin's and three cylinder models. If you are unsure on application please reach out to us, we are here to help! 
NEW OEM BRP Hexagonal Screw M10X 61420441990
This OEM BRP Secondary Clutch Driven Pulley is compatible with Maverick X3 Turbo RR or Turbo R 2017 and newer models. OEM part number 420686738 Your existing belt will work just fine, although installing a new belt at this time is a great idea! We can direct you if you need help finding the right one for your machine.- OUT OF STOCK
Fitment: DCP30 Can-Am Drive clutch governor cup puller
Replaces DPC25OEM 529036350
2015-18 Maverick 1000R Turbo
2017+ Maverick X3 Turbo (including P drive)
2018+ Defender HD8 HD10
2018+ Maverick Trail 800R 1000 1000R
2019+ Maverick Sport 800R 1000 1000R
2020+ Commander 800R 1000RAides in safe disassembly of the drive clutch for servicing.
Use with Gboost drive clutch puller # TOOL31SDGBOOST Instructional Video CLICK HERE
Features:
All GBoost® pullers start out with annealed, cold-rolled alloy steel.
Oil Quenched
Tempered
Rockwell hardness between 50-55
Zinc plated to prevent rust and thread deterioration
Machined to exact specifications in the U.S.A.
This results in31% higher tensile strength
19% higher yield strength
Stronger than any existing OEM pullers 
NEW OEM BRP Primary Clutch
Part number 420686870
Maverick X3 P-Drive Pully. This is a great way to upgrade your 2021 and older Maverick X3
Your existing belt will work just fine, although installing a new belt at this time is a great idea! We can direct you if you need help finding the right one for your machine.
The P-drive is a smoother engaging, less clunky, faster responding clutch when compared to the 2021 and older models.
Your existing M14X165 bolt and washer will work just fine when installing this clutch.
Brand NEW aftermarket primary clutch two way bearing with shims Current part number 22-51782 Includes new bearing and two washers This two way bearing service kit includes everything you need to replace the two way bearing on the primary clutch. The thrust washers install on either side of the two way bearing. Replacing this bearing is a great place to start if you experience hard shifting, creeping while in gear or premature belt failure. This kit replaces the two way bearing, 42083235, 420233418 and both thrust washers 420427220 Will not fit mavericks with a rear driveshaft, if you have fitment questions please reach out, we are here to help.
Fitment: Can-Am X3 Driven clutch- 2017-2020 Maverick X3 / 900 H.O. Models.
- Replaceable adapter ends.
- Easily removes pins without damaging clutches
- No slide hammer necessary for removal.
- Replaceable adapter ends.
- Zinc plated to prevent rust and improved strength.
- Tool comes with 2 replacement tips.
- Heat Treated.
NEW OEM Primary Clutch Puller. 529000064 Fits: Can-Am 1000 Defender 2016+ HD8 DH10 Maverick Trail 2018+ 1000 Maverick Sport (all) 2018+ Maverick X3 (all models) 2017+ Will not fit machines with M12 primary bolts
Brand NEW OEM Genuine CVT Transmission Drive V Belt Will fit Maverick and X3. Will also fit other machines. Must check part numbers to confirm fitment. Will work on Ski Doo snowmobiles as well Current Part Number 417300571 Old Part Numbers 422280655 417300531 422280651 IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT. FITMENT QUESTIONS?? PLEASE ASK!
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.