- SHIPS FREE TO THE LOWER 48 STATES This shaft has been cut and re-phased. Canam Maverick Rear prop shaft from gear box to rear differential. We install the guard. NEW # 703500994 Replaces:703500938,703500856, 705501849, 705502005, 703500994 20 spline gearbox yoke 20 spline differential yoke **Please note, this is the most updated shaft and does not require a wear ring on the differential side of the shaft. The last two pictures illustrate this.**
- Outer CVT cover for Turbo V twin Mavericks 1000R Best to pull your cover and visually inspect it for fitment. This cover has two holes over the primary clutch and one on the secondary. If you are unsure on fitment, please contact us! Fits: 2015-2018 Maverick 1000R Turbo 2017-2018 Maverick 1000R XMR Will not fit Maverick X3 Part number 420212285 replaces 420212282
- NEW OEM O-rings and hex bolts to install inner CVT cover on most Can-Am V-twins. Works on 7 and 13 bolt inner covers Part numbers: O-rings - 420430407 and 420631087 old numbers 420430408 420631088 Hex Bolts - 420440207 Also has a nut and washer for 1000 cover installation - 232561434, 224061121 Will come as pictured
- CVT cover set for Turbo V twin Mavericks 1000R Best to pull your cover and visually inspect it for fitment. This cover has two holes over the primary clutch and one over the secondary. If you are unsure on fitment, please contact us! Fits: 2015-2018 Maverick 1000R Turbo 2017-2018 Maverick 1000R XMR Will not fit Maverick X3 Comes with: Maverick Turbo covers inner and outer. CVT Cover Gasket CVT plug PTO O-ring Gear box O-ring Inner CVT Bolts/Nut 13 Cover screws Part numbers 420212285 420611407 420440568
- OUT OF STOCKBrand New Moose Utility left or right rear axle Will fit CAN AM Maverick 1000 2013-2015 Low profile stainless steel clamps Engineered in the USA Part Number: 0214-1145 Replaces OE Number: 705501948 705502356
Canam CVT Cover Kit Commander/Maverick 1000R
Please look at pictures to verify fitment.
This outer cover has two breather holes, one in front of the primary, one on the secondary.
This outer cover is the factory replacement for 420612319, some aftermarket clutches will not clear the new breather hole style you may need to modify this cover or backdate it to the 420612313 style with out the secondary breather.
Please look at pictures to verify fitment.
Fits:
Commander 1000R two seat 2018-2020
Commander 1000R MAX four seat 2018
Maverick 1000R two seat 2014-2018
Maverick 1000R MAX four seat 2014-2018Will not fit:
2015-2018 Maverick 1000R Turbo
2017-2018 Maverick 1000R XMRInner cover 420612304
Outer cover 420212286
13 Hex head CVT housing bolts 420440568
Gasket 420430126
O-rings – 420430407 and 420631087
Hex Bolts – 420440207
Also has a nut and washer – 232561434, 224061121
Nylon drain plug and clamp- This model type is a rubber O.D. seal with two sealing lips. The main sealing lip is spring loaded. This is a two-way seal, which means that it can retain lubricant and exclude contaminants simultaneously Canam Vtwin crankshaft main seal. Replaces OEM number 420631933 This seal is pressed into the PTO cover on v-twin's Unsure on fitment? Just measure you seal. 52mm Outer Diameter 34mm Inner Diameter 8mm Thick
- SHIPS FREE TO THE LOWER 48 STATES Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and 2020 & Prior Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail World’s Best Belt Line
- Latest generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market.
- Highest shock load rating to date being able to withstand the power of the 400hp machines.
- Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
- Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
- Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
- Latest bottom cog design for greater rotational efficiency at full shift.
- Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
- Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
- Increased cord pop-out resistance.
- neapco Brand U joint for front drive shafts These U joints are made in Italy, please do not confuse these with the sub-grade china made u joints. Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts. Maverick/Commander front driveshafts Will not fit: Maverick X3/Sport/Trail or Defender Includes clips, and grease fitting. Pro tip: Install grease fitting before pressing in u joint. Install u joint in a manner where you can still grease the joint in chassis. Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
- High quality Timken axle oil seal. Fits ATV front differentials 2006-current, some UTV's To be 100% sure on fitment, measure your outer diameter on your seal, it should read 47mm This seal has a 25mm inner diameter 47mm outer diamter and is 7mm thick. Replaces OEM 705500255 705500081 Order qty two per machine.
- High quality aftermarket Timken or SKF axle oil seal. Fits ATV rear differentials 2015-current, some UTV’s To be 100% sure on fitment, measure your outer diameter on your seal, it should read 52mm This seal has a 30mm inner diameter 52mm outer diamter and is 8mm thick. Replaces OEM 705501556 Order qty two per machine.
- UNI Foam air filter You will need to oil this filter before use. Fits SXS pictured: Commanders 800/1000 and Maverick 1000R (non turbo) (non X3/Sport/Trail) Unsurpassed in airflow, stopping dirt and overall performance Two-stage air filters come apart for maximum airflow and ultimate cleaning Most filters feature the Ultra Seal grease groove on the sealing surface Each fits in stock air box exactly like OEM filter Clean easily with grease-cutting dish washing detergent; just clean, oil and reuse indefinitely Flexible seams that will not crack Filters are designed to fit all stock air boxes Made in the U.S.A. Replaces OEM 707800327
- OUT OF STOCKCanam Maverick Outer CVT Cover 1000R Heat Protection Mat. New OEM. Will come as pictured. Current Part number: 715900313. Replaces: 420975053.
Single forged piston kit with rings, pin and clips, order two per engine
1000R Maverick this is a +1mm bore of the oem 420686094 piston allowing you to re use your factory cylinders with a fresh bore from your local machine shop
This takes your 976 cc 1000R engine to 997 cc
Factory head gaskets work just fine with these pistons no need for special made gaskets
Forged pistons compared to cast pistons, forgings are tougher and more durable, and will stand up to the abuse that high performance motorsport applications require. Most castings are brittle, have no grain structure and tend to fail catastrophically when the material yield strength is exceeded. Forgings have condensed grain that is aligned to the features of the part, which produces higher mechanical properties, and resistance to impact and fatigue. Each forging is designed to optimize the strength-to-weight ratio, and maximize performance.
12:1 CR (Compression Ratio) same as factory
The piston skirts feature ArmorGlide™ Coating this is the ultimate in skirt coating toughness, lubrication, and bond technology working together to minimize friction, maximize horsepower, and provide improved wear resistance.
New NGK Spark Plug
OEM part number 715900357
NGK part number LMAR9D-J
These spark plugs work in 2015-2017 Maverick TURBO machines only (will not work in the X3)
Shell
Thread Size: 10mm
Thread Pitch: 1.0mm
Seat Type: Gasket
Resistor Value: 5K Ohm
Reach: 26.5mm (1.04″)
Hex Size: 9/16″ (14mm)
Terminal Type: Solid
Overall Height: ISO
Gap: .031″ (0.8mm)Center Electrode
Material: Nickel
Type: Standard
Size: 2.5mm
Projection: ProjectedGround Electrode
Material: Nickel
Type: Multi-Ground- EPI brand Wheel bearing Greaser Tool for bearings with 30mm inner diameter Quick and easy way to extend the life of your wheel bearings 10 pumps of marine rated grease into a new wheel bearing will extend the bearing’s life High quality CNC machined with precision drilled grease channel Axle stub needs to be removed to use the tool. Part numbers: 3811-0094 CA30MMGREASER-O
- EPI roller kit Part number WE210933 The rollers in this kit were designed by The Clutch Guys to replace the stock composite rollers. They are CNC machined and hardened for a long service life. The stock composite rollers that Can Am uses tend to flat-spot very quickly, resulting in greater friction and reduced primary clutch reaction. Upgrade to these custom metal rollers for improved clutch function. The kit includes 6 custom metal rollers with bushings, 6 roller pins and 12 roller washers Replaces oem numbers: 420233893, 417223257, 420229995, 417223767, 420626230, 420626231