- New OEM 18 spline yoke with fully machined surface This is the forward most yoke on the rear driveshaft of G1 ATVs Fits years 2006 and newer, 450 and larger machines, if you are unsure on fitment please contact us. Use with 398 type U joints Current Part number 715900101 Replaces 705500371 705501372
- NEW OEM Winch Switch 710002052 New Genuine OEM Can-Am 4 Wheel Drive Switch This operates the winch on your SXS This is a two position momentary rocker switch. Fits: Commander, Maverick and Maverick Turbo, Maverick X3, Maverick Sport, Defender If you aren’t sure if this will fit, please ask, we will help! Part number 710002052
- Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
- HD Clutch bolt set for most every Can-am V-twin 2006 to current. Will not work on: Maverick Turbo Maverick X3 Maverick Sport Maverick Trail Defender These will swap out the factory Torque To Yield (TTY) bolts/studs. M10 and M12 Black-Oxide Alloy Steel Socket Head Bolt These are class 12.9 bolts, with a tensile strength of 170,000 psi, these alloy steel bolts are stronger than Grade 8 steel bolts. 8 and 10mm Allen Sockets required to install these bolts. 18-8 Stainless Steel Single-Wave Washers included, these help prevent loosening, use with your existing washers. Installation Torque Specs: 80 ft·lb On the Primary Bolt 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
- Can Am Outlander Renegade Front U Joint These are found on the front prop shaft of G1 ATV’s and front drive shaft of Commander and Maverick (non X3/Sport/Trail) Also used on the 400 rear drive shaft 22mm caps. This is a new OEM part Replaces Part numbers: 703000023 703500814 703500607 703500135 703500002 703000024 715900183 715900325
20 Spline Yoke Fits: XMR 1000, Maverick and ’14 & newer Commander style Rear differentials. You will need a wear ring if you are using this on the differential side of the shaft. These yokes are made to very tight tolerances, if you are not careful when installing these you can damage the yoke or your pinion shaft. We recommend you take your time and clean the pinion gear before installing. —Great for custom applications— Uses Factory size U joint (398 at the auto parts store) Part numbers 715900271
- NEW Chrome Conical Taper M10 Lug Nut Set of 16 M10x1.25 thread size 60 Degree taper 14mm Hex head size, great for use with aftermarket wheels where socket space is a concern These will work on every Canam ATV since 2006 and most every Canam sxs Will not fit the Maverick X3 12mm wheel studs. Part numbers: 57-94121, ALUG14BX
- Can-Am Rear Transmission Seal. Fits Large Gear Boxes, Standard and Low Ratio. Brand New OEM Seal OUTPUT SHAFT SEAL found on rear of gearbox, just in front of the rear driveshaft. This is the seal that goes on the rear, where the rear driveshaft goes out to the rear differential. If you are unsure if this is correct, please measure your current seal. If you get close to these specs it should work, the other option is much smaller in outer diameter. 72mm outer diameter 35mm inner diameter Current part number: 420831955 420831956