Our Custom USA Made Maverick Swap Kit. Allows you to run the better/stronger OEM Maverick Differential in your Commander. Kit includes: Custom Black Powder coated Brackets All Hardware needed New OEM Maverick differential New OEM Driveshaft with correct yoke and seal protector installed. No welding needed BUT you will need to cut/drill part of your frame to make this fit. Stock axles will work, no stretched arms or lift needed. The maverick differential is considerably more quiet than the stock Commander unit. Maverick differentials have proven to hold up much better, often referred to Can-am’s first real SXS rear differential. The gear ratio is the same as your stock Commander differential. Will not fit in commanders with un locking differentials Maverick Differential Swap Instructions
SHIPS FREE TO THE LOWER 48 STATES Brackets for swapping in a Maverick Rear Differential in your Commander. USA Made Black powder coat MIG welded steel brackets.
SHIPS FREE TO THE LOWER 48 STATES OEM Can am Shaft cut to length for use with our maverick swap kit in your commander.
Can Am 2012-2015 G2 800/1000 Outlander Renegade Commander Will not fit 1000R Complete Engine Gasket Set Moose Racing Gasket kit 0934-3020
Air Pressure sensor, this goes in the Black plastic Intake manifold. Will work on any 2006 to current Can am Outlander, Renegade, Commander, Maverick, Defender 500 570 650 800 850 1000 XT XMR MAX or XXC The Manifold Absolute Pressure sensor or MAP sensor is a sensor that is attached to the intake manifold. The MAP sensor responds to changes in the intake manifold pressure (vacuum) and provides a reading of engine load. How it works is 5 volts DC is supplied to the sensor from the ECU. Inside the MAP sensor there is a resistor that moves in relation to intake manifold pressure. The resistor varies the voltage between about 1V to 4.5V (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. Part numbers: 420874650 707000564 707000995 0 261 230 030 ALFA ROMEO 46553045 ALFA ROMEO 46533518 CHERY S21-3614021 FIAT 46553045 FIAT 77364869 FIAT 7084986 FIAT 0000046553045 FIAT 46533518 LANCIA 46533518 LANCIA 0000046553045 LANCIA 46553045 MOOSE 2120-0994 PROTON PW810694 ROTAX (BOMBARDIER-ROTAX GMBH) 874 650 SCANIA 5166434
Moose Racing Air Filter Part Number 1011-2796 Fits SXS pictured: Commanders 800/1000 and Maverick 1000R (non turbo) (non X3/Sport/Trail) Engineered for maximum air flow, increasing horsepower Maintains premium protection by stopping the finest dust particles Flexible seams that will not crack Filters are designed to fit all stock air boxes Made in the U.S.A. Replaces OEM 707800327
800/1000 Top end Gasket set Includes: 2 Head Gaskets 2 Cylinder Base Gaskets 2 Valve Cover Gaskets 2 Exhaust port crush gaskets 2 Intake Manifold Seals 8 valve seals Various O rings for fuel injectors, coolant fittings etc.. Moose gaskets are made to the same high quality standards as OEM. Part number 0934-3017
Heavy-duty ball joint kits feature durable steel-on-steel design and an adjustable end cap, which allows slop to be taken up as they wear
Greased zerk fitting for easy grease delivery
Replaces OEM part numbers: 706201393 706201576 706202045
G2 ATV’s Commander, Maverick, Maverick X3, Maverick Sport, Maverick trail
Unsure on fitment, please ask!Moose Racing number 0430-1035
Heavy-duty ball joint kits feature durable steel-on-steel design and an adjustable end cap, which allows slop to be taken up as they wear
Greased zerk fitting for easy grease delivery
Replaces OEM part numbers: 706202044 706200741 706201370 706201394
G2 ATV’s Commander, Maverick. Unsure on fitment? Please ask!
Moose Racing number 0430-1036
- Sale!OUT OF STOCK
Brand New Moose Utility Division Left or Right Rear Axle Will fit CAN AM Commander 800 and 1000 2013-2015 Low profile stainless steel clamps Engineered in the USA Part Number: 0214-1003 Replaces OE Number: 705500960 705502359 705501456 705501481 
SHIPS FREE TO THE LOWER 48 STATES New Can Am Maverick or Commander Gear Box New Can-Am GEAR BOX this is the way to reduce the over all gear ratio on your can-am 1000 running larger tires. Current Part Number- 420686654 Replaces: 420686563, 420686562 & 420685807 NEW OEM Canam Part NOT A REBUILD, ALL NEW Brand New In The Box This is the LOW RATIO gearbox for the larger style gearbox equipped machines, please ask if you are unsure about fitment. **Top speed on our 2012 Commander 1000 is 62 mph (high range) with this gearbox and stock clutching and stock size tires** Gearbox ratios, this isn’t regurgitated info, this is us counting teeth inside of the gearbox. Ring and Pinon Gears 37/15=2.467 Intermediate 45/40=1.125 High Range 36/27=1.333 Low Range 46/17=2.706 Reverse 34/12=2.833 High Range Ratio 3.700 Low Range Ratio 7.509 Reverse Ratio 7.863
Can-am Side by Side (Commander 800 and 1000 and Maverick 1000R) 2011-2017 Upgrade dash set: Dash, Bracket, cover and hardware. All OEM, 0 Miles. Your engine hours will stay with the ECU, be sure to record your miles for your own records. The dash comes in km/h and will require BUDS programming to change it to mph. This can be done at your local dealer or we offer this free of charge with purchase if you would like to stop by or you can send us your ecu, dash, key and if you have power steering we would need the power steering module as well. Updated Speedometer Part Number 710004547 Cluster Support Part Number 707900013 Dash Part Number 707900124 The dash is designed to auto pair, but sometimes it will not auto pair and you will have to program them together with buds software. This can be done at your local dealer or you can send in your ecu, key(s), and DPS (power steering) to us for programming.
Differential Vent Tube 8mm diameter Part number 705501584
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.5:1 compression ratio This is a ready to bolt on kit Fits: Commander 1000 ATV 1000/1000R Defender HD10 and DH9 Maverick Sport 1000 Please note this kit will not fit the SXS 1000R due to the lower compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420685242 420685248 420623568 420623566 420630210 420245436 420216351 420685244 420296774
New Aftermarket 1000/1000R Crankshaft with Connecting rods and bearings. No core needed, ready to install. *Will not fit Defender Maverick Sport/Trail* Replaces OE parts: 420219735 420219736 420217556 420217559 420641477 420641475 420233726
New Aftermarket 650/800 Crankshaft with Connecting rods and bearings. No core needed, ready to install. Replaces OE parts: 420219665 420217425 420217429 420641640 420641645 420233980 420219745 420219746 This will work with DPS equipped machines.
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 10.3 compression ratio This is a ready to bolt on kit, this will work with 800HO 800R and 650 engines. If you install this on a 650 you will need to have your ecu flashed or a inline tuner installed. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420296775 420685714 420613586 420296774 420216270 420845106 420630210
Brand new aftermarket secondary clutch assembly This is found on many BRP ATVs. Please ask if you have fitment questions. Replaces OEM Part Part Numbers: 420280173 420280176 420280178 420932421 420280236 420280499 420245910 420245911 420220913 If your machine has a spring with pigtails you will need to use a spring without them as this aftermarket clutch does not have provisions for them. 420238176 OEM Black/Orange is a great substitute Installation Torque Specs: 45 ft·lb On the Secondary Bolt (red thread locker recommended, allow to set up overnight)
NEW AFTERMARKET STARTER SPRAG VTWIN Starter Clutch One Way Bearing for Can-Am Will come as pictured Replaces OE Part Numbers:420659112 420659111 420659261 420659263 420659260
NEW AFTERMARKET STARTER VTWIN Will come as pictured Part Numbers: 420684560 420684562 420684568 420684566
New aftermarket 91mm bore piston and cylinder kit with gaskets rings wrist pins and circlips 12.1 compression ratio This is a ready to bolt on kit Fits: 2013+ Maverick, Maverick Sport and Commander 1000R Please note this kit will not fit the ATV 1000R or any 1000 engine due to the compression ratio. No dowel pins included, you will need to transfer these from your engine Replaces OEM Part Numbers: 420623566 420623568 420686094 420685244 420296774 420630195 420216352 420216351 420630210
All Balls Racing Fuel Pump Assembly Sending Unit Part number 47-1026 Fits: 2013-18 Maverick 1000R 2020 and prior Commander 800 1000 1000R Replaces OEM part numbers 709000270 709000362 709000759
All Balls dual row tapered wheel bearing Features: High contact double lip seals with armor shield O-rings sealing ID of bearing for superior water and dirt exclusion High performance tapered bearing deliver on average 95% better static load and 86% dynamic load capabilities Hardened steel 52100 and tempered for maximum durability WILL NOT work with the Maverick X3 Replaces: 293350118, 705400088 and 293350040 Unsure on fitment? Here are the dimensions: 30mm Inner Diameter 60mm Outer Diameter 37mm Wide Seal included, not all applications use the seal.
New IKO, Koyo or NTN brand needle bearing B98 replaces 705500261 If you are unsure on fitment please reach out to us we will help.
Brand New Genuine OEM BRP logo sticker 20mm diameter Part number 516006224 replaces 219902677 704904616
Can-am OEM PTO and crankcase bearing install and removal tools. These are the OEM tools required to install bearings in the bottom end of your Can-am V twin engine correctly. Part Numbers 529035917 & 529036032
New Demon Heavy Duty Axle Front Left Fits: 2011-2020 Commander 800 800R 1000 1000R Part number PAXL-3001HD Replaces OEM 705400953 705401105 705401653 705401871 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Front Right (passenger) Fits: 2011-2020 Commander 800 800R 1000 1000R Part number PAXL-3002HD Replaces OEM 705400953 705401105 705401653 705401871 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
New Demon Heavy Duty Axle Fits: 2011-2015 Commander 800R/1000 without the rare option of a un locking rear differential. Part number PAXL-1156HD Replaces OEM 705500960 705501456 705501481 705502359 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
EPI Lower Ball Joint Replaces
OEM part #706202045
Manufacturer Part Number: WE350045
Fits: Gen 2 Outlander Renegade Commander Maverick (non X3/trail/sport)
EPI roller kit Part number WE210933 The rollers in this kit were designed by The Clutch Guys to replace the stock composite rollers. They are CNC machined and hardened for a long service life. The stock composite rollers that Can Am uses tend to flat-spot very quickly, resulting in greater friction and reduced primary clutch reaction. Upgrade to these custom metal rollers for improved clutch function. The kit includes 6 custom metal rollers with bushings, 6 roller pins and 12 roller washers Replaces oem numbers: 420233893, 417223257, 420229995, 417223767, 420626230, 420626231
30amp five pin relay OE supplier Song Chuan Replaces OE numbers 278002822 278002168 710001334 515176774 710000739 515176774
Brand new OEM can am flywheel or magneto puller. This includes the puller itself and the piece to protect the crank. This will work on the 330, 400, 450, 500, 570, 650, 800, 850, and 1000 Part Number: 529035748 & 529036034
Moose 20amp four pin relay Replaces OE number 710001778
SHIPS FREE TO THE LOWER 48 STATES Standard G2 Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken, SKF The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential.570/650 XMR machines do not have the true XMR differential.
Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Part number MMCA302 This belt is built specifically for the straight mud rider that needs a ton of belt squeeze to stop from slipping the belt. The specific compounds in this belt make it instantly grab when the clutching and tune are correct. Note: This blend of compounds and thickness will build more heat at higher speeds, so we recommend keeping it under 35mph Mud Monster Belt Line Higher strength compared to OEM and aftermarket drive belts. Mud Monster belts have been developed with the 2nd Generation compound called DUMAX2 for added strength, flexibility, and heat resistance. You can squeeze this belt a lot harder for more tuning possibilities and less slippage. Maximum under-cord stiffness allows the belt to flex for rotational efficiency and running cooler temperatures Built thicker when possible for more belt to sheave adhesion. Built for extreme abuse, and excessive shock load. Handles higher temps than OEM Built with Aramid fiber cord to eliminate stretching like a Polyester cord. Made in the USA!
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.