SHIPS FREE TO THE LOWER 48 STATES Set of Bearings and Seals to Rebuild Your Front Differential on Your Can-Am Fits Most Can-Am Models from 2007-Current (WILL NOT FIT Maverick X3/Sport/Trail or Defender) This Kit has High Quality Aftermarket Bearings which are: Timken, SKF, NSK, KOYO, Nachi Comes with: 2 - Carrier Bearings- SKF Brand 2 - Axle Bearings- OEM NSK Japan made 2 - Axles Seals- Timken 1 - Inner Pinion Bearing- Nachi Japan made 1 - Large Pinion Bearing- Koyo Japan made 1 - Pinion Seal
SHIPS FREE TO THE LOWER 48 STATES Standard G2 Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken, SKF The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential.570/650 XMR machines do not have the true XMR differential.
SHIPS FREE TO THE LOWER 48 STATES Late G1 Early G2 Standard Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 1 3/4" (47mm) To further verify fitment you can measure your pinion pilot shaft, this should be 9/16″ (14mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees.
EPI roller kit Part number WE210933 The rollers in this kit were designed by The Clutch Guys to replace the stock composite rollers. They are CNC machined and hardened for a long service life. The stock composite rollers that Can Am uses tend to flat-spot very quickly, resulting in greater friction and reduced primary clutch reaction. Upgrade to these custom metal rollers for improved clutch function. The kit includes 6 custom metal rollers with bushings, 6 roller pins and 12 roller washers Replaces oem numbers: 420233893, 417223257, 420229995, 417223767, 420626230, 420626231
Genuine Can Am 800R/1000 Green Fuel Injector OEM Part Part number: 420874833 replaces 420874830
New bearing and seal kit for 2014-19 Commanders 800R 1000 or 1000R These are high quality bearings and seals, brands include: Koyo, SKF and Timken This **WILL NOT** work for 2011-2013 Commanders This **WILL NOT** work for with Commanders Equipped with a LOCKING REAR DIFFERENTIAL. This **WILL NOT** work for 2020 Commanders Fits in differentials part numbers: 705502517 705501804 705502096 705502331
SHIPS FREE TO THE LOWER 48 STATES Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and 2020 & Prior Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Gates Part number 30R3750 Do not confuse this with the carbon or standard g-force, this is the newly developed for the 2020 season.DON’T BREAK YOUR BELT. BREAK IT IN.FEATURES AND BENEFITS Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity ― making it one of the most efficient CVT belts currently on the market.- First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
- Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
- Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
- Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
- Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
- Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.
If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.
1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)
2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.
SHIPS FREE TO THE LOWER 48 STATES! Can-am NEW OEM Main bearing set. Kit includes: Main Bearing Half with Oil hole 420233965 x2 Main Bearing Half without Oil hole 420233960 x2 PTO Cover Bearing 420233995 Be sure to mark your cases before pressing them out! The oil holes need to be lined up!
Fits all 500, 650, 800, 800R, 570, 850, 1000, 1000R and 1000R turbo Mavericks Outlanders, Renegades, and Commanders. Replaces OEM part numbers 715000302, 422280360, 715900212, and 422280364. This will not fit: Defenders, Maverick X3 or Maverick Sport/Trail Part number MMCA302 This belt is built specifically for the straight mud rider that needs a ton of belt squeeze to stop from slipping the belt. The specific compounds in this belt make it instantly grab when the clutching and tune are correct. Note: This blend of compounds and thickness will build more heat at higher speeds, so we recommend keeping it under 35mph Mud Monster Belt Line Higher strength compared to OEM and aftermarket drive belts. Mud Monster belts have been developed with the 2nd Generation compound called DUMAX2 for added strength, flexibility, and heat resistance. You can squeeze this belt a lot harder for more tuning possibilities and less slippage. Maximum under-cord stiffness allows the belt to flex for rotational efficiency and running cooler temperatures Built thicker when possible for more belt to sheave adhesion. Built for extreme abuse, and excessive shock load. Handles higher temps than OEM Built with Aramid fiber cord to eliminate stretching like a Polyester cord. Made in the USA!
NEW aftermarket cooling fan for G1 ATV’s Bolt on plug in and go, this is a nice alternative to the OEM Replaces OEM 709200124 709200371 709200313 709200229
Early Commander Steering Rack Great Value for replacing a worn out rack. Moose Number 0430-1071 Replaces OEM 709401185 Fits 2011-2014 Commander 800/1000 Be sure to center rack before installing your steering shaft.
SHIPS FREE TO THE LOWER 48 STATES OEM Outer CVT Cover 2013 Maverick 1000R ONE Breather hole in front of Primary clutch. This is the cover with the most room. Common to use this on newer Vtwin Mavericks with aftermarket clutches that do not require the extra breathers. Current Part Number: 420612313 replaces 420612312 Will not fit Maverick X3/Sport/Trail
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.