NGK 4339 DCPR8E Standard Plug Fits All G1 ATV's OE numbers: 707000246 715900637 Thread Size: 12mm Thread Pitch: 1.25mm Seat Type: Gasket Resistor Value: 5K Ohm Reach: 19mm (3/4") Hex Size: 5/8" (16mm) Terminal Type: Removable Nut (you will need to remove this for use on G1 ATV's) Gap: .028" (0.7mm) Torque Specs Aluminum: 10.8-14.5 lb. ft. Brand: NGK Heat Range: 8 Longevity: 30k Miles Resistor: Yes Projected Material: Nickel Quantity: 1
NEW OEM CVT cover with heat shield installed from factory
Fits:
Maverick 1000R two seat 2013-2014
Commander 1000 MAX four seat 2014-2016
Commander 800R MAX four seat 2017-2019ONE Breather hole in front of Primary clutch.
This is the cover with the most room. Common to use this on newer V-twin 1000R Mavericks with aftermarket clutches that do not require the extra breathers.
Please match this up with yours before purchasing.
Part number 420612318
Replaces 420612312 420612313 715900257 420975052
NEW Can Am OEM Cam Timing Tool For holding the cam in place for timing and tightening camshaft sprocket bolts For easy installation of new timing chains or just setting timing. OEM Number 529036268 replaces 529036231
Early Commander Steering Rack Great Value for replacing a worn out rack. Moose Number 0430-1071 Replaces OEM 709401185 Fits 2011-2014 Commander 800/1000 Be sure to center rack before installing your steering shaft.
Differential Vent Tube 8mm diameter Part number 705501584
CVT cover set for Turbo V twin Mavericks 1000R Best to pull your cover and visually inspect it for fitment. This cover has two holes over the primary clutch and one over the secondary. If you are unsure on fitment, please contact us! Fits: 2015-2018 Maverick 1000R Turbo 2017-2018 Maverick 1000R XMR Will not fit Maverick X3 Comes with: Maverick Turbo covers inner and outer. CVT Cover Gasket CVT plug PTO O-ring Gear box O-ring Inner CVT Bolts/Nut 13 Cover screws Part numbers 420212285 420611407 420440568
SHIPS FREE TO THE LOWER 48 SATES Can-am 2013 1000R Maverick Commander style CVT covers. This is the 13 bolt cover set. Popular for aftermarket clutch set ups. Only one breather hole in front of the primary clutch works on non Turbo Machines This kit will keep the water out! Comes with: 2013 Maverick 1000R covers inner and outer. CVT Cover Gasket CVT plug PTO O-ring Gear box O-ring Inner CVT Bolts/Nut 13 Cover screws Part Numbers: 420612312 420612313 420611407 420440568
EPI Bushing Kit, steel inner, plastic outer bushings and shimsFits: G2 Canam ATV’s Outlander or RenegadeDefender and CommanderIf you are unsure on fitment, please contact us before purchasing!Exact replacement components to return your suspension to like-new conditionKits are sold per A-armEPI Part Number: WE341052P/U Part Number: 0430-1029Replaces OEM Part Numbers: 703500875 706202088 706202089 706202133- OUT OF STOCK
New OEM Differential Pinion Oil Seal. Please check your wear ring, if that is grooved it is time to replace. Very easy to miss that and blame a new seal on a bad wear ring. Will fit: Gen 1 Front and Rear Diffs 2012-18 Outlander and Renegade Front and Rear Early Commander Rear All Maverick and Commander Front WILL NOT FIT G2 XMR 800/850/1000 REAR DIFFERENTIAL or 2019 and newer Measurements: 70mm outside diameter and 37mm inside diameter Part number 705401615 
Cast Aluminum Valve cover set with Stainless bolts. Replaces your factory plastic valve covers on any can-am V-twin ATV or UTV 500/570/650/800/850/1000/1000R Replaces OE Numbers: 420610390 420610394 420610393 420610395
Spicer Brand U joint for front drive shafts
Fits: G1 Renegade and Outlander . Also works on Outlander 400 Rear shafts.
Maverick/Commander front driveshaftsWill not fit: Maverick X3/Sport/Trail or Defender
Includes clips, and grease fitting.
Pro tip: Install grease fitting before pressing in u joint.
Install u joint in a manner where you can still grease the joint in chassis.Replaces OEM : 715900325 703000023 703000024 703500002 703500135 703500607 703500814
This model type is a rubber O.D. seal with two sealing lips. The main sealing lip is spring loaded. This is a two-way seal, which means that it can retain lubricant and exclude contaminants simultaneously Canam Vtwin crankshaft main seal. Replaces OEM number 420631933 This seal is pressed into the PTO cover on v-twin's Unsure on fitment? Just measure you seal. 52mm Outer Diameter 34mm Inner Diameter 8mm Thick
Have Questions?
Our staff is available to answer questions
canampartsguy@gmail.com
1340 Okray Ave.
Plover, WI 54467
jared@canampartsguy.com
Cant find What you're looking for?
Visit our 
store!
2016 Can Am Parts, LLC. All rights reserved.