Clutching

  • NEW CV Tech Primary Clutch Puller for can am ATVs Replaces OEM puller part number 529035746 7/8" Hex Head Measurements listed in picture We have found this to work on both the ATV factory primary and CV tech primary clutches. THIS IS NOT A TOOL RENTAL, IF YOU USE THE TOOL YOU OWN IT!
  • Can Am Maverick X3 Maverick Sport/Trail  or Defender Belt change kit. M36x2.0 thread size works on all X3’s and Defenders Will not fit QRS clutches found on “OG” mavericks This is a OEM tool and bolt Spreader It is recommended to use a coin in between the bolt and the clutch to avoid marring up the clutch. The bolt has the correct T30 bit on one end to remove the cvt cover bolts with your 13mm wrench/socket. We highly suggest a ratchet and T30 socket on a 3 inch extension to speed up the job. Part number 708200720 and 529000088 This set works in place of 708200686

  • New OEM Cap Fits on cover 420212500 Comes with 0-ring 420250050 Fits the following machines 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
  • Brand NEW OEM Genuine Transmission Belt 422280652 High Performance Drive V Belt TCIC (Turbo Charged Inter Cooled) Factory on 2020 Maverick X3 Turbo R R 195 HP models These will retro fit on all Maverick X3 models along with Defender H8/HD10 Maverick Sport/Trail. IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT. FITMENT QUESTIONS?? PLEASE ASK! Comes as pictured
  • Drive Belt Can Am Fits: 2017-2020 X3 Maverick Turbo R Turbo RR 900HO 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8 OEM # 422280651 / 417300383 / 422280654 / 422280652
    IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.
    FITMENT QUESTIONS?? PLEASE ASK!
    World’s Best Belt Line
    • Latest generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market.
    • Highest shock load rating to date being able to withstand the power of the 400hp machines.
    • Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
    • Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
    • Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
    • Latest bottom cog design for greater rotational efficiency at full shift.
    • Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
    • Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
    • Increased cord pop-out resistance.
    This belt is for the rider / racer that is looking for the latest in technology and proven performance. Made in JAPAN. WBB383
  • OUT OF STOCK
    New OEM Torx Screws Comes as a set of 11 Will fit on the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
  • Driven Pulley Extractor bolt for belt changes This spreads the secondary with the 708200686 adapter tool. Works with: Can Am Defender HD8 HD10 Part number 529036352
  • New OEM Gasket Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R
  • RHINO ROLLER Kit 2 Pack Driven Clutch Upgrade Fitment: All Can-AM Models w/2 Roller Driven Clutch
    • 2015-2017 Maverick 1000R Turbo XDS-DPS / Max
    • 2016+ Defender HD10 / MAX
    • 2016+ Defender HD8 / Max
    Replaces OEM # 420629211 / 417127016 ***MADE IN USA*** Designed for units with Over-sized Tires, Heavy Workload and High Horsepower. Made from the Latest Heat Resistant Compounds, which can withstand Continuous Heat up to 340 degrees. These Rollers Resist Flat Spotting, Provide Excellent Strength, Rigidity and Longevity.
  • Brand NEW OEM  BRP Genuine Transmission Drive Belt Will fit:  Defender, Maverick Trail 1000/1000R   Maverick Sport 1000/1000R Will also fit other machines. Must check part numbers to confirm fitment. Current Part Number:  417300551 Replaces 417300383 High performance drive belts calibrated to maximize your machine’s performance. Aramid tensile cords used in construction for extra long life and dependability, also delivers a consistent length. High tensile reinforced fiber elastomer undercords provide minimal dusting and long term flex life. Flexweave overcord for superior adhesion and crack resistance. Consistent performance during life of belt. Quality you can count on for optimum performance
  • Drive Belt Can Am Fits: 2017-2020 Maverick X3 900HO Turbo R Turbo RR 2017-2020 Maverick Trail/Sport 800R, 1000, 1000R 2016-2020 Defender HD10/HD8

    Replaces OEM # 422280651 / 417300383 / 422280654 / 422280652 Gates Part number 48R4289 If you have fitment questions, please ask, we are here to help.

    IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.

    FEATURES AND BENEFITS
    Designed for the most demanding, turbo-charged off-road CVT applications. With Gates proprietary materials and design, G-Force™ RedLine™ CVT belts handle extreme temperatures with excellent heat recovery, while maximizing load and torque capacity - making it one of the most efficient CVT belts currently on the market.

    • First on the market to utilize Ethylene Elastomer compound to address the needs of larger SxS and high-horsepower ORVs in tough riding conditions.
    • Next-generation EE compound offers maximum transverse stiffness and heat resistance, resulting in higher load capacity, higher peak torque capacity, less “heat fade” and less speed loss.
    • Delivers 75% greater dynamic axial stiffness on average, up to 50% lower speed losses and better recovery from temperatures up to +170°C (+338°F) without power loss.
    • Unmatched Temperature Capability – Runs cooler, resists glazing for better recovery and reduced cracking/chunking out after running at temps exceeding +149°C (+300°F).
    • Extended Belt Life – Belt life increased 100-300% versus aftermarket competitive belts in severe duty lab test conditions and in field testing.
    • Higher Power Capacity – Reduced speed (rpm) loss by 50% under high loads and increased load capacity by >10% compared to other aftermarket belt.

     

    DON’T BREAK YOUR BELT. BREAK IT IN.

    If you don’t break the belt in properly, you’ll find yourself shredding the belt instead of the terrain. In fact, most powersports belt failures can be attributed to improper break-in and clutch adjustment – or not breaking in the belt at all. Follow these steps to ensure the best performance and longest life from your G-Force™ belt.

    1. Clean the clutches according to manufacturer specifications and clean the sheaves with a Scotch-Brite™ pad. Remove old belt residue, glazing, oils, and debris with alcohol or acetone on the clutch sheave area. Be sure your breather tubes are free of any belt material (broken belt material gets everywhere)

    2. Install and Break It In. Perform two heat cycles (10-15 minutes each) at +27°C (+80°F) at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. If belt installation is at a temperature of +16°C (+60°F) or below, perform two heat cycles in 20 minutes at 30-40 mph (2-wheel drive) with cover installed. Bring the belt temperature down to normal operating temperatures, then shut down and let cool for 30 minutes. Repeat the process a second time. Conservatively run through the entire shift range, without exceeding ¾ throttle. Bring the belt back to normal operating temperature (15 minutes) then shut down and completely cool the belt for 30 minutes. Repeat the process.

  • FREE SHIPPING TO THE LOWER 48 STATES New OEM clutch inner cover Will fit on the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R Does not included mounting hardware or o-rings. Comes as bare cover
  • NEW EPI Primary Clutch Puller. PCP-15 (PCP15)

    Fits: Can-Am 1000 Defender 2016+ HD8 DH10
    Maverick Trail 2018+ 1000
    Maverick Sport (all) 2018+
    Maverick X3 (all models) 2017+

    Replaces oem 529000064

    One piece style, manufactured from the highest quality steel

    Precise machining on every model for accuracy

    Heat treated for superior strength

  • OUT OF STOCK

    Brand NEW OEM Genuine CVT Transmission Drive V Belt Will fit Maverick and X3. Will also fit other machines. Must check part numbers to confirm fitment. Will work on Ski Doo snowmobiles as well Current Part Number 417300531 Old Part Number 422280651 IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.  FITMENT QUESTIONS?? PLEASE ASK!

  • NEW Gboost Primary Clutch Puller. DCP19 Fits: Can-Am Defender 2016-20 HD8 DH10 Maverick Trail 2018+ Maverick Sport (all) 2018+ Maverick X3 (all models) 2017+ Replaces oem 529000064 All GBoost pullers start out with annealed, cold-rolled alloy steel. Oil Quenched Tempered Rockwell hardness between 50-55 Zinc plated to prevent rust and thread deterioration Machined to exact specifications in the U.S.A. This results in 31% higher tensile strength 19% higher yield strength Stronger than any existing OEM pullers
  • FREE SHIPPING TO THE LOWER 48 STATES New OEM cover Will fit the following 2016-2019 Defender HD8 and HD10 2018-2019 Maverick Trail 800R and 1000R 2019 Maverick Sport 1000R Old part number 420212502 New part number 420212500 O-ring and drain plug cap are NOT included
  • NEW OEM BRP Hexagonal Screw M10X 61
    420441990
  • NEW OEM BRP Drive Belt. Part number 422280225 This fits the big single cylinder models 2022+ Outlander 700 Outlander HD7 Pro Commander 700 Maverick Trail 700 Defender HD7 Traxter HD7 FITMENT QUESTIONS?? PLEASE ASK! Comes as pictured
  • Fitment: DCP30 Can-Am Drive clutch governor cup puller

    Replaces DPC25OEM 529036350

    2015-18 Maverick 1000R Turbo
    2017+ Maverick X3 Turbo (including P drive)
    2018+ Defender HD8 HD10
    2018+ Maverick Trail 800R 1000 1000R
    2019+ Maverick Sport 800R 1000 1000R
    2020+ Commander 800R 1000R

    Aides in safe disassembly of the drive clutch for servicing.
    Use with Gboost drive clutch puller # TOOL31SD

    GBOOST Instructional Video CLICK HERE

    Features:

    All GBoost® pullers start out with annealed, cold-rolled alloy steel.

    Oil Quenched
    Tempered
    Rockwell hardness between 50-55
    Zinc plated to prevent rust and thread deterioration
    Machined to exact specifications in the U.S.A.
    This results in

    31% higher tensile strength
    19% higher yield strength
    Stronger than any existing OEM pullers

  • Brand NEW aftermarket primary clutch two way bearing with shims Current part number 22-51782 Includes new bearing and two washers This two way bearing service kit includes everything you need to replace the two way bearing on the primary clutch. The thrust washers install on either side of the two way bearing. Replacing this bearing is a great place to start if you experience hard shifting, creeping while in gear or premature belt failure. This kit replaces the two way bearing, 42083235, 420233418 and both thrust washers 420427220 Will not fit mavericks with a rear driveshaft, if you have fitment questions please reach out, we are here to help.
  • NEW OEM Can Am Tool M8x1.25 Tapered Bolt Part number 529036098. This tool fills a few roles, used to open the secondary clutch on many models. This will also lock the crankshaft on Vtwin's and three cylinder models. If you are unsure on application please reach out to us, we are here to help!
  • NEW OEM Primary Clutch Puller. 529000064 Fits: Can-Am 1000 Defender 2016+ HD8 DH10 Maverick Trail 2018+ 1000 Maverick Sport (all) 2018+ Maverick X3 (all models) 2017+ Will not fit machines with M12 primary bolts  
  • NEW OEM BRP Drive Belt.

    Part number 422280226

    This fits the 2023+ Outlander 500/Hd5 big single cylinder models

    FITMENT QUESTIONS?? PLEASE ASK!

    Comes as pictured

  • Brand NEW OEM Genuine CVT Transmission Drive V Belt Will fit Maverick and X3. Will also fit other machines. Must check part numbers to confirm fitment. Will work on Ski Doo snowmobiles as well Current Part Number 417300571 Old Part Numbers 422280655 417300531 422280651 IF YOUR MAVERICK HAS A REAR DRIVESHAFT (OG MAVERICK) THIS BELT WILL NOT FIT.  FITMENT QUESTIONS?? PLEASE ASK!

Title