Differential & Gearbox

  • Brand New Genuine OEM Wear ring a must if you are replacing your pinion seal, these are the sacrificial parts that save your drive shaft from grooving! Will fit 18 and 20 Spline Yokes that are fully machined Part Number 705400036
  • New Aftermarket Bellows with clamp, use this in place of vent lines on your differentials. Replaces OEM part number: 705400352
  • SHIPS FREE TO THE LOWER 48 STATES Can-am Outlander,Renegade or Commander 500 650 800 1000 6 Bolt HD rear Differential. This is an OEM Canam part used in many Generation 1 atvs. It has the bracket for the rear brake caliper on it. This is an updated version with much more substantial webbing for improved support. Fits: 2006-2011Outlander and Renegade 500 650 800 800 2012 Outander MAX 400 500 650 800 2011 2012 Outlander 800XMR 2006-14 Outlander 400 2011-2013 Commander 800 1000 Current Part Number 703501033 Previous Part Numbers 703500892 705502069 705501569 Interchanges with: 705500774 705500822 705501412 705500891 705501093 705501047 705501997
  • Cam Am rubber bellow for front or rear differential. This is a brand new OEM rubber bellows. Part number 705400352
  • Brand New Genuine OEM Fill Level Plug Be sure that yours looks the same due to other styles for front or rear differential from different years M14 diameter 1.5 thread pitch Part number 705500504
  • SHIPS FREE TO THE LOWER 48 STATES Our Custom-Made Maverick Swap Kit. Allows you to run the better/stronger OEM Maverick Differential in your Commander. Kit includes: Custom Black Powder coated Brackets All Hardware needed New OEM Maverick differential New OEM Driveshaft with correct yoke and seal protector installed. No welding needed BUT you will need to cut/drill part of your frame to make this fit. Stock axles will work, no stretched arms or lift needed. $450 for the brackets and hardware alone. $350 for the shaft alone. The maverick differential is considerably more quiet than the stock Commander unit. Maverick differentials have proven to hold up much better, often referred to Can-am’s first real SXS rear differential. The gear ratio is the same as your stock Commander differential. Will not fit in commanders with un locking differentials Maverick Differential Swap Instructions
  • Please verify your differential uses this style of Seals before ordering! Can Am Front Differential Pinion and Axle Seals (Timken) Fit on most all 2006-2019 Outlanders and Renegades Also fits Commanders and Mavericks (non X3/Sport/Trail) The Pinion Seal has a 70mm Outer Diameter And the standard 37mm inner diameter. Replaces part numbers 705401481 705500255 705500081 The Axle Seal has a 47mm Outer Diameter And the standard 25mm inner diameter. Replaces part numbers 705401618 705401486 Complete Seal kit for Standard Front Differentials
  • Outlander Renegade Commander Maverick Differential Drain Plug Brand New Genuine OEM Drain Plug 9.9 mm outside diameter Will fit on some fronts and rears be sure yours looks like this one and measures the same Part Number 705500894
  • Please verify your differential uses this style of Seals before ordering! Can Am Standard Rear Differential Pinion and Axle Seals (Timken or SKF) Please measure your parts before ordering to verify fitment. The Pinion Seal has a 70mm Outer Diameter and the standard 37mm inner diameter. Replaces part number 705401481 The Axle Seal has a 52mm Outer Diameter And the standard 30mm inner diameter. Complete Seal kit for Standard Rear differentials common to find in 2016 and newer ATVs or if your differential has been repalced.
  • SHIPS FREE TO THE LOWER 48 STATES Standard G2 Rear Differential Bearing and Seal Kit High quality aftermarket bearings along with double lip axle seals. Bearing and Seal Brands include: Nachi, KOYO, NTN, Timken, SKF The large case sealing and pinion gear O-rings are NOT included as a cost saving measure, these O-rings are reusable if not damaged. There are a few options for kits, please verify your differential uses this style of gears before ordering! This will only fit six mounting hole differentials. Open up the differential! Check for two bearings total (one on each side) on the ring gear. If you only have two proceed to the next measurement. Measure your outer diameter of your axle seals! They should measure close to 2 1/16″ (52mm) To further verify fitment you can measure your pinion pilot shaft, this should be 5/8″ (16mm) The last pictures show this very clearly. Please take the time to measure your parts before buying this will save time and restocking fees. Fits 2015 and newer G2 style ATV 500/570/650/800/850/1000/1000R NON-XMR style REAR differential.570/650 XMR machines do not have the true XMR differential.
  • SHIPS FREE TO THE LOWER 48 STATES This will replace the functionality of the VISCO Lock in any Can-am Front differential. 2006 to Current including X3. Installs in place of the “spider gears” Will not fit models with an electronic smart lok front differential Very simple to install. One measurement to make. The TORQ Locker is the most advanced, strongest, highest quality automatic locking differential on the planet, proven in the most extreme vehicles from hard-core Rock Crawling, racing the King of the Hammers, Rock Bouncing, Sand Dunes and Mud Drags. To back this all up, Torq-Masters Industries offers an unprecedented 4 year warranty on the TORQ Locker with no tire size, horsepower limits or loopholes, quadruple the warranty of any other automatic locker on the market. Torq-Masters Industries is committed to building the highest quality locking differentials possible. To be the best, we build with the best, TORQ Locker is 100 percent Made in the USA with 100 percent USA raw materials. Keep it Simple, no air-lines to leak, compressors to fail, cables to adjust or electrical gremlins, the TORQ Locker gives you piece of mind as a reliable, mechanical, automatic locker that can handle any terrain. The TORQ Locker design eliminates and integrates pesky locker components seen in all other automatic drop-in lockers. The spacers are gone and the dowel pins are now machined into the Cam Gears to form key-ways. The innovative design features of the TORQ Locker have three game-changing benefits: No dowel pins to install or fail. The Key-Way design of the Cam gears can’t shear, ever. Easiest Locker on the market to install, no spacers, no dowel pins, one measurement. Best On-Road manners of any automatic locker; the Key-Way design is more forgiving than the rigid dowel pin design. The Key-Way allows for smoother locker engagement. By eliminating the spacers they eliminated the leading cause of the pop some people experience with automatic lockers. Listing is for the TORQ Locker only. Differential carrier shown in pictures is for reference only.
  • Cam Am rubber bellows for front differential or rear differential This is a brand new OEM rubber breather and a OEM Oetiker Clamp Bellows Part # 705400352