- OUT OF STOCKOEM Can-am Low Beam Headlight Does not include any mounting brackets or hardware, what is pictured is what is shipped to you. Fits: Renegade, Commander and Maverick (non X3/Sport/Trail) Will not fit on Outlanders. Outlanders use reflector style headlights on the low beams. Part Number: 710002524
- OUT OF STOCKSHIPS FREE TO THE LOWER 48 STATES New Forged OEM Can-am piston kit with rings. Matched to an OEM Rotax used Cylinder. This is ready to install on your 650 Outlander engine. Two are required per engine. Piston comes with rings installed. Piston pin, and clips are not included. Part number 420684111 420613888
- OUT OF STOCKNEW OEM Can-Am Maverick X3 Right Sway Bar End Link (Also called RH Ball Joint) Fits RIGHT Front on Can-Am Maverick X3 and X3 MAX's Part Number: 706202765
- Can Am Commander 800 1000 Dual CVT Air Intake 2011 2012 2013 2014 2015. Complete kit to upgrade CVT cover from 1 inlet - 1 outlet to 2 inlets - 2 outlets. Keeps CVT system cooler in extreme use conditions. Reduction in belts temps range from 40 to 70 degrees! Used in conjunction with Snorkel Kit to get maximum airflow to CVT while under extreme conditions. Needed to install Snorkel Kit (715001728) on Commander. Part Number: 715002467.
- New Genuine OEM Robust injected-polypropylene construction allows for the right fit and easy installation Adjustable unit safely holds smartphones or small tablets with a length or width measuring between 2.9" (7.5 cm) and 5.1" (13.0 cm) with or without protective case Integrated storage 0.6 Gal Guiding wire grooves to pass charging cable through the lid Possibility of relocating 12V power outlet or installing USB outlet in storage compartment Not compatible with windshields and Snorkel Kit
Fitment: DCP30 Can-Am Drive clutch governor cup puller
Replaces DPC25OEM 529036350
2015-18 Maverick 1000R Turbo
2017+ Maverick X3 Turbo (including P drive)
2018+ Defender HD8 HD10
2018+ Maverick Trail 800R 1000 1000R
2019+ Maverick Sport 800R 1000 1000R
2020+ Commander 800R 1000RAides in safe disassembly of the drive clutch for servicing.
Use with Gboost drive clutch puller # TOOL31SDGBOOST Instructional Video CLICK HERE
Features:
All GBoost® pullers start out with annealed, cold-rolled alloy steel.
Oil Quenched
Tempered
Rockwell hardness between 50-55
Zinc plated to prevent rust and thread deterioration
Machined to exact specifications in the U.S.A.
This results in31% higher tensile strength
19% higher yield strength
Stronger than any existing OEM pullersNEW SEIZMIK STRIKE Side mirror set
Both drivers and passengers side mirrors
Fits 2.0″ Round Roll Cages or the 1.875″ Round Roll Cages with the supplied rubber shims
Features: Adaptive 360 Bracket Rotation: Will accommodate any angle roll cage pillar & provide optimal viewing position, so you can mount it high or low and adjust to perfect position every time
Full Breakaway Geometry: Designed to break away during impacts to prevent damage
Convex mirrors more than double your field of rear view
High-Impact ABS Plastic Housing: Resists damage
Ball Socket Joint: Provides a broad range of viewing angles
Heavy-Duty Steel Mounting Clamp: Low mass design provides maximum strength and durability
Convex Mirror Surface: provides wider viewing ranger and image stabilization
Shatter Resistant Safety Glass Position Tension Adjustment Bolt: Always be able to keep it tight as newUNLIMITED LIFETIME WARRANTY
CANAM Cage Styles
Defender: Pro Fit Cage
Maverick Trail/Sport: Pro Fit Cage
OG Maverick/Commander: Round 2.0”Part number 18092
- NEW GENUINE OEM part Part number 705600679 Includes: 715500333 715500383 705600080 715500335 715500337 This is the drivers side front caliper left hand side Fits two seat models: 2011 Commander 800 2012-2020 Commander 800R 2011-2017 Commander 1000 2013-2015 Maverick 1000R STD XRS XXC 2016-2018 Maverick 1000R STD DPS XC XXC WILL NOT FIT TURBO, XMR, OR MAX MODELS
New OEM Can Am Outlander, Renegade 1000R XXC Gearbox
Current Part Number- 420686568
Previous Part Numbers- 420686565 NEW OEM Canam PartNOT A REBUILD, ALL NEW Brand New In The Box
Fits- Maverick 1000R, Commander 1000 or 800, Outlander 1000 2012-2014, all Outlander XMR 1000/1000R, Renegade 1000/1000R.
If unsure of fitment, please contact us. We will be happy to help!These ratios are published in the 2019 Service manual, we have not confirmed these to be accurate.
Ring and Pinon Gears 37/15=2.467
Intermediate 45/40=1.125
High Range 36/27=1.333
Low Range 46/17=2.706
Reverse 34/12=2.833Overall Gear Ratios:
High Range 3.700
Low Range 7.510
Reverse Range 7.863- New Demon Heavy Duty Axle Fits: 2011-2015 Commander 800R/1000 without the rare option of a un locking rear differential. Part number PAXL-1156HD Replaces OEM 705500960 705501456 705501481 705502359 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty
- New Demon Heavy Duty Axle Front Right (throttle side) Fits: G1 ATV Outlander/Renegade 500 650 800HO 800R Part number PAXL-1127HD Replaces OEM 705400292 705400479 705400508 705400660 705400935 705401110 Through years of research and development Demon Powersports has developed an axle that doesn’t burn a hole in your pocket and adheres to the highest quality standards. These axles are bigger, beefier, and stronger. Demon Heavy Duty Axles are built using larger CV joints and shafts, paired with our proprietary dual heat treatment process, and 4340 Chromoly Steel inner CV cage gives these the axles the edge it needs for superior strength and longevity. These axles also utilize a unique double plunge design which allows it to achieve higher articulation angles approximately, the axles are designed to slide on the bar splines allowing for 1.5 inches of travel and 40° articulation over terrain on the inboard joint. The outboard joint can travel 0.5inches and swing from 45°-47° depending on the model. The Demon heavy duty axles are equipped The TPEE (Thermoplastic polyester elastomer) boots which are stronger, stiffer, more fatigue resistant, puncture resistant, and more temperature resistant than a standard OEM boot. Axles use molybdenum grease to provide low friction and smooth motion. Trust in Demon Heavy Duty Axles to keep you riding!! • 15%-20% increase in diameter compared to regular axle • Inner cage made up of 4340 chromoly steel • Dual heat treated high strength chromoly steel shaft • Thermoplastic polyester elastomer (TPEE) Boot • 10%-15% increase in CV joint size compared to regular joints • Wider articulation angles • Dual plunge design prevents axle from binding • Packed with high load molybdenum grease Precision CNC machined • Can Fit 1.5”- 5” Bracket lift of particular brands/ All Portal Gear Lifts / 1.5”- 5” A-arms of particular brands • 1-year ltd warranty